background image

English

18V Cordless Drill/Driver 

 

 

  

Operator’s Manual                GCD18BK

•  Do not charge battery pack 

when temperature is below 50 degrees F (10 degrees 

C) or above 104 degrees F (40 degrees C). Store tool and battery pack in a location where 
temperature will not exceed 122 degrees F (50 degree C). This is important to prevent serious

 

damage to the battery cells. 

•  Place charger on flat non-flammable surface 

and away from flammable 

materials when re-charging the battery pack

•  To reduce risk of electric shock, 

unplug charger from outlet before attempting any 

maintenance or cleaning. 

•  If operating time has become excessively shorter, 

stop operating 

immediately. It may result in a risk of overheating, possible burns and even an explosion. 

•  Battery leakage may occur 

under extreme usage or temperature conditions. Avoid 

contact with skin and eyes. If liquid comes in contact with your skin, wash immediately with soap 
and water. If liquid gets into your eyes, wash them out with clear water for at least 10 minutes, and 
then seek medical attention right away.

•  Do not attempt to use a step-up transformer, 

an engine generator or DC power 

receptacle.

•  Do not short the battery pack. 

Do not touch the terminal with any conductive material. 

Avoid storing battery pack in a container with other metal objects such as nails, coins, etc. Always 
protect the battery terminals when battery pack is not used.

•  Do not charge battery pack inside a box or container of any kind. 

The 

battery must be placed in a well ventilated area during charging. 

•  Do not allow anything to cover or clog the charger vents.
•  Do not incinerate the battery pack even 

if it is severely damaged or is completely 

worn out. The battery pack can explode in a fire. 

•  Disconnect Charger from the power source when not in use. 

This will 

reduce the risk to electric shock or damage to the charger if metal pieces should fall into the 
opening. It also will help prevent damage to the charger during a power surge.

 

WARNING:

 

A battery short can cause a large current flow, overheating, 

possible burns and even a breakdown

 

WARNING:

 

120 volts are present at charging terminals, do not probe 

with conductive objects. Electric shock or electrocution may result. Do not 
allow any liquid to get inside charger. Electric shock may result.

 

 

WARNING:

 This product comes with the battery installed internally. You 

are not allowed to install or remove the battery from the product. 

IMPORTANT BATTERY INFORMATION: DISPOSING THE 
BATTERY PACK

•  Your batteries are 

Nickel-Cadmium 

rechargeable batteries. Certain Local, State and  

 

Federal laws prohibit disposal of these batteries in ordinary trash.

•  Consult your local waste authorities for your disposal/recycling options.

•  More information regarding battery disposal in U.S. and Canada is available at;
  http://www.rbrc.org/index.html, or by calling 1-800-822-8837 (1-800-8BATTERY).

Summary of Contents for GCD18BK














Reviews: