Generex CS121BL User Manual Download Page 82 | Manualshive

Page: 82 / 166

background image

80

Using the integrated Webserver, the SITESWITCH 4 enables the monitoring and the remote
control of its 4 power outputs. The power sockets can be switched on and off individually. This
can be done either manually via the HTML browser interface or UPSMON or automatically
using the EVENT manager of the CS121 - or any other network CS121 or compatible device.
When executing the action using the EVENT manager of the CS121, the power switching can
be preconfigured to run with delays or to run on a schedule. Both the UPSMON time scheduler
and the HTML time scheduler can be used to configure a power switching time schedule.
This task can also be achieved using the full version of the UNMS UPS Network Management
Software.

Note:

(only  SS4,  not  SS4AUX)  If  you  wish  to  use  a  UPS  with  your  SS4  then
you  must  install  the  appropriate  CS121  Firmware  on  your  SS4.  The
default  Firmware  on  SS4  (OEMID  27)  is for  the  usage  without  UPS,  as
standalone  remote  powerswitch.  For  UPS  usage  at  the  SS4  you  must
also be sure to set the Exchange COM Ports checkbox and then use the
configuration cable (not included) to connect the SS4 with your UPS.

Figure 96:

Exchange COM Ports 1 & 2 for SS4

7.1.1

SS4 Feature overview

4 configurable powers sockets with a breaking capacity of 230V/8A

Power socket status indicator via HTML, UPSMON, UNMS or SNMP

Control via the internal CS121 or via remote CS121 or RCCMD compatible devices

Remote control of the powers sockets via HTML Browser (Password protected)

LED-Status of the power sockets

Small metal casing with 1.5RU, designed for 19"-Rack Mountings (mounting frame included)

High breaking capacity (8A), input with IEC 16A.

Programmable power switching via the HTML and UPSMON Scheduler

Delay of alarm (e.g. UPS alarms) triggered power switching on COM1 of the CS121

7.1.2

SS4 Contents

SITESWITCH 4

16A IEC 230V power cable

2 mounting irons for 19“-Rack installation

manual for SS4

The manuals are being constantly updated and therefore the reader is encouraged to check
our

website for

a newer

download

version of the adapter manual. Check

http://www.generex.de for manual updates.

7.1.3

SS4 Installation

The power consuming devices are connected to the SS4 using IEC 250 VAC/6A plug cables.
The SS4 has 4 IEC 250VAC/6A chassis sockets that can be switched on and off separately.

«
...
80
81
82
83
84
...
»

Summary of Contents for CS121BL







































































































































































Reviews:

No comments

Related manuals for CS121BL

Brand: J4C Pages: 4

Brand: ABB Pages: 6

Brand: Warren Controls Pages: 28

Brand: EAS Electric Pages: 89

Brand: Samson Pages: 32

Brand: Quantum Pages: 15

Brand: National Instruments Pages: 29

Brand: Harmonic Drive Pages: 85

Brand: ICP DAS USA Pages: 166

Brand: ICP DAS USA Pages: 5

Brand: ICP DAS USA Pages: 64

Brand: ICP DAS USA Pages: 7

Tunnel Master Jr

Brand: ICS Pages: 83

PROFIBUS PROFI-2510

Brand: ICP DAS USA Pages: 4

Brand: ICP DAS USA Pages: 40

Brand: Lawler Pages: 4

Brand: QTP Pages: 2

Brand: Uniden Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands