background image

WARRANTY

INFORMATION

General Tools & Instruments’ (General’s)
EP8709 Calibratable 4-Function Thermo-
Hygrometer is warranted to the original
purchaser to be free from defects in
material and workmanship for a period of
one year. Subject to certain restrictions,
General will repair or replace this
instrument if, after examination, the
company determines it to be defective in
material or workmanship.

This warranty does not apply to damages
that General determines to be from an
attempted repair by non-authorized
personnel or misuse, alterations, normal
wear and tear, or accidental damage. The
defective unit must be returned to General
Tools & Instruments or to a General-
authorized service center, freight prepaid
and insured.

Acceptance of the exclusive repair and
replacement remedies described herein is a
condition of the contract for purchase of this
product. In no event shall General be liable
for any incidental, special, consequential or
punitive damages, or for any cost, attorneys’
fees, expenses, or losses alleged to be a
consequence of damage due to failure of, or
defect in any product including, but not
limited to, any claims for loss of profits.

15

Summary of Contents for EP8709

















Reviews: