manualshive.com logo in svg

General CL10, User Manual, Page: 5 / 20

Share
Download
General CL10 User Manual Download Page 5

PRODUCT OVERVIEW

1. LCD

2.

(

POWER

on/off) button

3. Transmission power (I, II or III) 

LEVEL SEL.

button

4. Transmitting code 

START/STOP

transmission button

5. Transmitting 

CODE SEL.

button. 

Press and hold to

enter selection mode; press briefly to exit.

6. 

▼

button (press to reduce power level/change

transmitting code). Levels I, II and III and codes 
F (default), E, H, D, L, C, O and A are available.

7. 

▲

button (press to increase power level/change

transmitting code)

8. 

(Mute) on/off button

9. 

(Flashlight) on/off button

10. + jack

11. 

(ground) jack

12. Flashlight (on top)

13. Fold-out stand (on back)

14. Battery compartment (on back)

1. 

(Transmitter battery status) icon

2. Transmission power level (I, II or III)

3. Transmitting code

4. AC line voltage

5. DC line voltage

6. Line voltage measured (in voltmeter mode)

7. Transmitting status

8. Code being transmitted

9. Transmission signal amplitude

10. 

(Line voltage detection mode) icon

11. 

(Mute on) icon

5

쐉

씈
씉

Fig. 2. The transmitter’s controls,
display and physical features

Fig. 3. All possible indications on
the transmitter’s LCD

Summary of Contents for CL10





















Reviews:

No comments