Model 88™
CABLE MAINTENANCE
To get maximum service from your cables, be sure
that they are clean and well oiled. This not only
provides running lubrication, but greatly extends
the life of the cables as well. Our SNAKE OIL is
ideally suited for this purpose, since it not only
lubricates the cables, it deodorizes them as well.
TROUBLE SHOOTING GUIDE (Table 3)
Problem Probable
Cause
Solution
Operator forcing the cable.
Do not force the cable. Let the cutter do the work.
Too much slack between machine and drain.
Do not allow slack between machine and drain.
Cable used in wrong size drain line.
A cable that is too large or too small in diameter for a line is
more likely to kink. (Consult Table 1—Cable Applications.)
Cable kinks or breaks.
Cable exposed to acid
Clean and oil cables regularly.
Cable tangles or kinks.
Operator forcing the cable.
Do not force the cable. Let the cutter do the work.
Motor stops while foot pedal is
depressed
Hole is pedal or hose.
Replace as required.
Motor turns in one direction but
not other.
Reverse switch failure.
Replace reverse switch.
Damaged power cord or extension cord.
Replace cords.
Short circuit in motor.
Take motor to authorized repair center.
Ground Fault Circuit Interrupter
trips and will not reset.
Faulty ground fault circuit interrupter.
Replace Ground Fault Circuit Interrupter.
Motor turns but cable does not.
Safety Clutch engaged.
Do not force cable.
PARTS LIST
Cat. No.
Description
Cat. No.
Description
88-100
Frame Complete
88-235
Spring Washer (2)
88-101
Frame Only
88-240
Locking Washer
88-110
Axle
88-245
Clutch Shaft (5/8”)
88-120
5” Caster
88-300-1
Motor & Gear Head Complete
88-120-1
6” Caster
88-300-2
Motor & Gear Head Complete
88-121
Caster Bolts (4)
88-301
Motor (1725 RPM) Disc. (See 88-300-1)
88-130
Front Bearing Post
88-301-1
Motor (3450 RPM)
88-130-A
Bushings (2)
88-301-2
Motor (1750 RPM)
88-130-B
Grease Fitting
88-302-1
Gear Head Only (7 to 1 Ratio)
88-130-C
Post Adjusting Bolts (2)
88-302-2
Gear Head Only (3.5 to 1 Ratio)
88-131
Post Bolts, Nuts, & Washers (3)
88-302-A
Gear Head Vent Cap
88-150-1
Handle Hinge Assembly
88-302-1-A
Gear Head Vent Cap
88-150-1-A
Hinge Top
88-303
Gear Head Mounting Bolts (4)
88-150-1-B
Hinge Bottom
88-305
Motor Mounting Bolts,Nuts & Washers(4)
88-150-1-C
Hinge Roll Pins (2)
88-310
20 ft. Power Cord with GFCI
88-155-1
Handle Locking Sleeve
88-311
Air Foot Switch & Rev. Switch Complete
88-160-2
Handle with Pedal Holder
88-311-A
Box Only with Cover & Screws
(from Serial #1270 and Over)
88-311-B
Foot Pedal and Hose
88-160-2-A
Locking Collar Shop Screw
88-311-C
Clamps (2)
88-170
10” Wheel
88-311-D
Foot Pedal
88-171
Hat Type Push Nuts (2)
88-311-E
Power Switch Diaphragm
88-172
Spacer Washers (2)
88-311-F
Air Hose (11 ft.)
88-190
Plastic Clutch Face Cover
88-311-G
Reverse Switch
88-200
Clutch Assembly
88-311-H
Rubber Boot (Rental Units Only)
88-201
Clutch Housing with Set Screws
GFI-88
Ground Fault Circuit Interrupter
(Through Serial #1797)
5/8 G-CDC
Cable Drive Coupling with “G”
88-201-1
Clutch Housing with Set Screws
Connector for 5/8” Shaft
(Serial #1798 & Over)
1/2 G-CDC
Cable Drive Coupling with “G”
88-205
Drive Plate
Connector for 1/2” Shaft
88-205-A
Round Socket Head Bolts 1”x1/4”(6)
5/8 L-CDC
Cable Drive Coupling with “L”
88-210
Clutch Hub with Roll Pin
Connector for 5/8” Shaft
88-215
Adjustment Nut
1/2 L-CDC
Cable Drive Coupling with “L”
88-215-A
Brass Slotted Head Screw 1/2” (2)
Connector for 1/2” Shaft
88-220
Friction Disc (2)
7/8 L-CDC
Cable Drive Coup. for 6L78 7/8" Cables
88-225
Spacer Bushing
88-DECAL
Set of Safety Decals
88-230
Fixed Plate
88-VIDEO
Instructional Video
SEE BACK COVER FOR SCHEMATIC DIAGRAM
7
