Generac Power Systems PowerMate 1020 Owner'S Manual Download Page 8

6

Owner’s Manual for Water Pump

Add Engine Oil

There is no oil in the engine. The crankcase

must be filled before starting the engine for the

first time.

NOTE: Use petroleum based oil for engine

break-in before using synthetic oil.

1. Place water pump on a level surface.
2. Verify oil fill area is clean.
3. Remove oil fill cap and wipe dipstick clean.

See Figure 2-2.

Figure 2-2. Remove Dipstick

4. Add recommended engine oil to the

bottom of the oil fill hole (A).
– Above 40°F (4°C), use SAE 30
– Below 40°F (4°C) and down to 10°F

(-12°C) use 10W-30

– All temperatures, use synthetic 5W-30

.

Figure 2-3. Recommended Oil

5. Thread dipstick into oil filler neck. Oil level

is checked with dipstick fully installed.

6. See Figure 2-4. Remove dipstick and

verify oil level is within safe operating

range above the lower limit (L).

Figure 2-4.  Safe Oil Operating Range

7. Install oil fill cap/dipstick and hand-tighten.

Add Fuel

Fuel requirements are as follows:
• Clean, fresh, unleaded gasoline.
• Minimum rating of 87 octane/87 AKI (91

RON).

• Up to 10% ethanol (gasohol) is acceptable.
• DO NOT use E85.
• DO NOT use a gas oil mix.
• DO NOT modify engine to run on alternate

fuels. Stabilize fuel prior to storage.

1. Verify equipment is OFF and cooled for a

minimum of two minutes prior to fueling.

2. Place equipment on level ground in a well

ventilated area.

3. Clean area around fuel cap (A) and

remove cap slowly.

Figure 2-5. Add Recommended Fuel

4. Slowly add recommended fuel up to the

filler neck (B). Do not overfill.

IMPORTANT NOTE: 

Fuel should not be

visible in the filler neck.
5. Install fuel cap.

(000135)

CAUTION

Engine damage. Verify proper type and quantity of 
engine oil prior to starting engine. Failure to do so 
could result in engine damage.

000719

A

SAE 30

10W-30

Synthetic 5W-30

000399

000116

L

(000105)

DANGER

Explosion and Fire. Fuel and vapors are extremely 
flammable and explosive. Add fuel in a well 
ventilated area. Keep fire and spark away. Failure to
do so will result in death or serious injury. 

(000204)

DANGER

Explosion and Fire. Do not overfill fuel tank. 
Overfilling may cause fuel to leak and ignite or
explode, resulting in death or serious injury.

000671

A

B

Summary of Contents for PowerMate 1020





















Reviews: