Generac Power Systems MAGNUM MLT4250 Owner'S Manual Download Page 22

Page: 22 / 49

Operation

Owner’s Manual for MLT Light Tower

MDC List of Alarms

No.

Events

Specification

Protection

Type

Information on

Binary Output

Available

Description

AnInIOM Sd

YES

Shutdown alarm configurable on the input of IG-IOM/IGS-
PTM.

AnInIOM Wrn

WRN

YES

Warning alarm configurable on the input of IG-IOM/IGS-PTM.

Battery Flat (low

battery)

YES

If the controller switches off during starting sequence due to
bad battery condition, it doesn’t try to start again and acti-
vates this protection.

Binary Input

CONFIG.

YES

Configurable Warning/Shutdown alarms on the inputs of IL-
NT.

ChrgAlternFail

WRN

YES

Failure of the alternator to charge the battery.

EmergencyStop

If the red emergency stop switch is pushed or opened, shut-
down is immediately activated.

Engine Temp Sd

Water temperature is greater than

Sd Water Temp

setpoint.

Engine Temp Wrn

WRN

YES

Water temperature is greater than

Wrn Water Temp

setpoint.

Fgen<, >

YES

The generator frequency is out of limits given by

Gen >f

and

Gen <f

setpoints.

Fuel Level Sd

YES

Fuel level is smaller than

Sd Fuel Level

setpoint (5%). (Not

available on MLG, MLT or MTT units.)

Fuel Level Wrn

WRN

YES

Fuel level is smaller than

Wrn Fuel Level

setpoint (15%). (Not

available on MLG, MLT or MTT units.)

GCB fail

Failure of the generator circuit breaker.

Igen unbl

The generator current is unbalanced.

Low BackupBatt

WRN

RTC backup battery is flat (low).

Oil Press Sd

Oil pressure is smaller than

Sd Oil Press

setpoint.

Oil Press Wrn

WRN

YES

Oil pressure is smaller than

Wrn Oil Press

setpoint.

Overload

YES

The load is greater than the value given by

Overload

setpoint.

Overspeed

YES

The protection comes active if the speed is greater than

Overspeed

setpoint.

ParamFail

NONE

Wrong checksum of parameters. Happens typically after
downloading new firmware or changing of the parameter. The
controller stays in INIT mode. Check all parameters, write at
least one new parameter.

PickupFault

Failure of the magnetic pick up sensor for speed measure-
ment.

Sd IOM fail

Shutdown alarm in case of lost connection to IOM/IGS-PTM
module.

SprinkIActive

WRN

The protection is active if the output

Sprinkler

is closed.

Start failed

YES

Unit did not start.

Stop fail

YES

Unit did not stop.

Vbat

WRN

YES

Battery voltage is out of limits given by

Batt Undervolt

set-

points.

Underspeed

YES

During starting of the engine, when the RPM reaches the
value of

Starting RPM

setpoint, the starter is switched off and

the speed of the engine can drop under

Start RPM

again.

Then the

Underspeed

protection becomes active. Protection

evaluation starts 5 seconds after startup.

Vgen<, >

YES

The generator voltage is out of limits given by

Gen <V

and

Gen <V

setpoints.

Discount-Equipment.com

Summary of Contents for MAGNUM MLT4250


















































Search results

Summary of Contents for MAGNUM MLT4250

Reviews:

Brands by name

Popular brands

Generac Power Systems MAGNUM MLT4250, Owner'S Manual

Search results

Summary of Contents for MAGNUM MLT4250

Reviews:

Brands by name

Popular brands