Generac Power Systems LINKTower PLT240 Owner'S Manual Download Page 7

Introduction and Safety

Owner’s Manual for PLT240 Light Tower

3

Starting the Unit

DO NOT

 start a unit in need of repair.

Raising and Lowering the Mast

IMPORTANT NOTE: Unit wind rating is 45 mph.

ALWAYS

 extend the outriggers and level the unit

before raising the mast. 

DO NOT

 retract the

outriggers while the mast is up.

Keep area around the unit clear of people while
raising and lowering the mast.

ALWAYS 

lower the mast when not in use.

Service Safety

This unit uses high voltage circuits capable of causing
serious injury or death. Only a qualified and licensed
electrician should troubleshoot or repair problems
occurring in this equipment.

Before servicing the unit, verify the main breaker
switch and circuit breakers are in the OFF (O)
position, and the shore power cord is disconnected.

DO NOT

 perform even routine maintenance unless

all electrical components are shut down.

ALWAYS 

use extreme care when servicing this unit

in damp conditions. Do not service the unit if your
skin or clothing is wet. Do not allow water to collect
around the base of the unit.

DO NOT

 wash the unit with high pressure hoses,

power washers, or steam cleaners. Water may
collect in the unit, causing damage to electrical parts. 

Replace all missing and hard to read decals. Decals
provide important operating instructions and warn of
dangers and hazards.

Wear heavy leather gloves when handling winch
cables. Never let cables slip through bare hands.

Only use mild soap and water to clean the lens covers.
Other chemicals may damage the lens covers.

Safety and Operating Decals

See 

Table 1-1

 and 

Figure 1-1

. This unit features numerous

safety and operating decals. These decals provide
important operating instructions and warn of dangers and
hazards. The following diagrams illustrate decal locations
and descriptions.

Replace any missing or hard-to-read decals and use care 
when washing or cleaning the unit. Decal part numbers 
can be found in the parts manual at 

www.generacmobileproducts.com.

DANGER

Electrocution. DO NOT use the unit if
electrical cord is cut or worn through. Doing
so will result in death or serious injury.

(000263a)

WARNING

       Electrocution. Do not set up or operate 
       this unit if severe weather is expected.
Lightning strikes can kill or cause severe injury
even if you are not touching the unit.

(000296)

WARNING

(000345)

Personal Injury. Do not set-up or operate unit 
in high winds. Doing so could result in death,
serious injury, property, or unit damage.

WARNING

Personal Injury. Stop immediately if the mast hangs 
up or the winch cable develops slack. Excess slack 
could cause the mast to collapse, resulting in personal 
injury or equipment damage.

(000265)

WARNING

Personal injury. Use caution when winding 
winch cable. Failure to do so could result
in serious injury.

(000391)

Table 1-1. Decal Descriptions

ID

Description

1

Warning—Entanglement Hazard

2

Lifting Point

3

Notice—Correctly Wind Winch

4

Warning—Crushing Hazard

5

Danger—Electrical Storms, High Wind and Overhead 
Wires

6

Notice—Interconnect (located on flat beneath right 
side receptacles)

7

Quick Start Guide

8

Warning—Hazardous Voltage: Disconnect Before 
Servicing

9

Lock Stabilizing Feet

10

Forklift Pocket: Not a Step

11

Notice—Adjust Four Stabilizers

12

Warning—Electric Shock Hazard

Summary of Contents for LINKTower PLT240





























Reviews: