manualshive.com logo in svg

Generac Power Systems 66781, Owner'S Manual

Share
Download
Generac Power Systems 66781 Owner'S Manual Download Page 43

Maintenance

Owner’s Manual for Stationary Diesel Generators

37

5.7.8— Check and Adjust V-Belt 

5.7.8.1— Check

Check the V-belt deflection. Too little belt deflection accelerates belt wear, while too much deflection leaves the pulley 
idle, overheats the engine, and no-load is generated. Adjust the belt deflection as follows:

1.

On right side of enclosure, loosen two clamps at each end of turbocharger exhaust outlet pipe. Remove pipe, 
clamps and rubber couplings from engine. 

2.

Remove oil drain hose from holding clamp.

3.

Remove four screws with nylon washers to release fan guard from radiator shroud. 

4.

Perform visual inspection as follows:

•

Inspect belt for cracks, fraying, excessive wear or other damage.

•

Verify that belt is free of grease and oil. Replace belt if contaminated.

NOTE: Use a solution of soap and warm water to clean pulleys, if necessary. Avoid use of solvents, but if 
used, always follow by a soap and water wash.

5.

Using a suitable gauge, apply 22 Ibs (10 kgf) force midway between the crankshaft and alternator pulleys. See 
Figure 5-13.

6.

Take note of gauge reading. If belt deflection is not within specification, see Subsection 5.7.8.2—Adjust.

7.

Install four screws with nylon washers to fasten fan guard to radiator shroud. 

8.

Install oil drain hose into holding clamp.

9.

Install clamps and rubber couplings onto each end of turbocharger exhaust outlet pipe. Install pipe to turbo-
charger outlet and radiator shroud. Tighten clamps.

Figure 5-13. Check V-Belt Deflection

Belt Condition

Deflection

New

8-12 mm

Used

10-15 mm

 Alternator Pulley

Crankshaft Pulley

Belt Deflection Gauge

Summary of Contents for 66781





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands