manualshive.com logo in svg

Generac Power Systems 6.75, Operator'S Manual

Share
Download
Generac Power Systems 6.75 Operator'S Manual Download Page 3

CONTACT US AT 

1-888-545-6576

         3

 

Chapter 1: General Safety Rules 

Labels 

Your TRIMMER/MOWER carries prominent labels as reminders for its proper and safe use.  Shown below are copies of the Safety 
and Information labels that appear on the equipment. Take a moment to study them and make a note of their location on your 
TRIMMER/MOWER as you set up and before you operate the unit. Replace damaged or missing safety and information labels 
immediately. 

Protecting Yourself and Those Around You

Read this safety & operating Instructions manual before you use the TRIMMER/MOWER.  Become familiar with the operation 
and service recommendations to ensure the best performance from your machine. If you have any questions or need assistance, 
please contact us at 1-888-545-6576 and one of our Technical Support Representatives will be happy to help you. 

This is a high-powered machine, with moving parts operating with high energy at high speeds.  You must operate the machine 
safely.  Unsafe operation can create a number of hazards for you, as well as anyone else in the nearby area.  Always take the 
following precautions when using this machine: 

 

Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people, their property, and 
themselves. 

 

Always wear protective goggles or safety glasses with side shields while mowing to protect your eyes from possible thrown 
debris. 

 

Avoid wearing loose clothing or jewelry, which can catch on the mower’s moving parts. 

 

We recommend wearing gloves while mowing.  Be sure your gloves fit properly and do not have loose cuffs or drawstrings. 

 

Wear shoes with non-slip treads when using your TRIMMER/MOWER.  If you have safety shoes, we recommend wearing 
them.  Do not use the machine while barefoot or wearing sandals with exposed toes or heels. 

 

Wear long pants while operating the TRIMMER/MOWER. 

 

Use ear protectors or ear plugs rated for at least 20 dba to protect your hearing. 

 

Keep bystanders at least 50 feet away from your work area at all times.  The tips of the cutting cords on the 
TRIMMER/MOWER can throw sticks, small stones, gravel, and bits of debris over long distances at great velocity.  Do not 
travel over loose materials such as gravel or mulch with the trimmer head spinning.  Doing so could cause personal injury or 
property damage from thrown objects.  Release the bail bar to stop the spinning cords and shut off the engine when another 
person or pet approaches. 

 

Never tamper with safety devices.  Check their proper operation regularly. 

 

Never operate the machine when under the influence of alcohol, drugs, or medication. 

 

In an emergency, to quickly stop the cutting cords, remove your hand from the bail bar. 

#13649 

#14823 

#13758 

#32343 

Summary of Contents for 6.75









































Reviews:

No comments

Brands by name

Popular brands

Load more brands