Generac Power Systems 005982-0, Owner'S Manual, Page: 6 / 20

4
Remove all packaging material. •
Remove separate accessory box. •
Remove the generator from carton. •
Check all contents. If any parts are missing or damaged, locate an
authorized dealer at 1-888-436-3722.
1 - Owner’s manual •
1 - Oil SAE 30 •
3 - Product Registration Cards (English, Spanish, French) •
2 - 8” WHEELS •
1 - Axle •
1 - Frame Foot •
1 - Handle with grip •
1 - Hardware Bag •
1 - Plastic Spacer 2 - M8-1.25 x 40 Bolts
1 - Handle Bracket 1 - M6-1.0 x 40 Bolt
2 - Rubber Bumpers 2 - M8-1.25 x 16 Bolts
2 - Cotter Pins 1 - M6-1.0 Hex Flange Nut
2 - M8-1.25 Hex Flange Nuts
The generator requires some assembly prior to using it. If problems
arise when assembling the generator, please call the Generator
Helpline at 1-888-436-3722.
The wheels are designed to the unit to greatly improve the
portability of the generator.
NOTICE:
The wheels are not intended for over-the-road-use.
1. Refer to Figure 1 to install the wheels as shown.
• Slide the axle through the frame brackets.
• Slide on the wheels then install the cotter pins.
2. Refer to Figure 1 to install the wheel bumpers as shown.
• Secure the two rubber bumpers to the frame foot
using two M8-1.25 Hex Flange Nuts (if not already
assembled).
• Place the frame foot under the frame and secure with two
M8-1.25 x 16 bolts.
3. Refer to Figure 2 to install the handle assembly as shown.
• Install the handle bracket to the frame using two M8-1.25
x 40 bolts (if not already assembled).
• Slide the plastic spacer onto the handle assembly then
align with the holes in the handle bracket (if not already
assembled).
• Secure the handle assembly to the handle bracket using
the M6-1.0 x 40 bolt and one M6-1.0 hex flange nut.
Figure 1 – Wheel Assembly
Figure 2 – Handle Kit
M8-1.25 x 40
BOLTS
1 X M6-10 HEX FLANGE NUT
1x HANDLE W/GRIP
1x PLASTIC SPACER
1x M6-1.0X40 BOLT
1x HANDLE BRACKET
Read the Owner’s Manual and Safety Rules before operating
this generator.
Compare the generator to Figures 3 through 6 to become
familiarized with the locations of various controls and adjustments.
Save this manual for future reference.
1. 120 Volt AC, 20 Amp, Duplex Receptacle – Supplies electrical
power for the operation of 120 Volt AC, 20 Amp, single-phase,
60 Hz electrical lighting, appliance, tool and motor loads.
2. 120/240V AC, 20 Amp Locking Receptacle – Supplies
electrical power for the operation of 120 and/or 240 volt AC,
20 amp, single-phase, 60 Hz, electrical lighting, appliance,
tool and motor loads.
3. Circuit Breakers (AC) – Each receptacle is provided with a
2-pole, 14 amp circuit breaker to protect the generator against
electrical overload.
4. Air Filter – Filters intake air as it is drawn into the engine.
5. Choke Knob – Used when starting a cold engine.
6. Fuel Tank – Tank holds 4 U.S. gallons of fuel.
7. Grounding Lug – Ground the generator to an approved earth
ground here. See "Grounding the Generator" for details.
8. On/OFF Switch – Controls the operation of the generator.
General Information