Genelec Oy, Olvitie 5
FIN - 74100 IISALMI, FINLAND
Phone:
+358 - 17 - 83881
Telefax:
+358 - 17 - 812267
Web:
http://www.genelec.com
E-mail:
Genelec document D0001R001a
COPYRIGHT GENELEC OY 8.2001
All data subject to change without prior notice
Genelec Inc, 7 Tech Circle
Natick, MA 01760, USA
Phone:
+1 - 508 - 652 - 0900
Fax:
+1 - 508 - 652 - 0909
E-mail:
AMPLIFIER SECTION
AMPLIFIER SECTION
AMPLIFIER SECTION
AMPLIFIER SECTION
AMPLIFIER SECTION
Amplifier output power with an 8 Ohm load (Short
term):
Bass
120 W
Midrange
120 W
Treble
120 W
Long term output power is limited by driver unit
protection circuitry.
Slew rate:
80V/µs
Amplifier system distortion at nominal output:
THD
<0.05%
SMPTE-IM
<0.05%
CCIF-IM
<0.05%
DIM 100
<0.05%
Signal to Noise ratio, referred to full output:
Bass
>100 dB
Midrange
>100 dB
Treble
>100 dB
Mains voltage:
100/200V or 115/230V AC
Voltage operating range: nominal ±10%
Power consumption:
Idle
30W
Full output
200W
CROSSOVER SECTION
CROSSOVER SECTION
CROSSOVER SECTION
CROSSOVER SECTION
CROSSOVER SECTION
Analog input connector:
XLR female
pin1 gnd
pin2 +
pin3 -
Input impedance:
10 kOhm
Input level for maximum short term output of
111 dB SPL @1m:
variable from +17 to +5 dBu
Output level for -6 dBu analog input:
variable from 88 to 100 dB SPL@1m
Subsonic filter below 33 Hz :
18 dB/octave
Ultrasonic filter above 60kHz:
12dB/octave
Crossover frequency:
bass/mid
420 Hz
mid/treble
4 kHz
Crossover acoustical slopes:
18 - 24 dB/octave
Crossover level control operating range in 1 dB
steps:
bass
from 0 to -6 dB
mid
from 0 to -6 dB
treble from 0 to -6 dB
Bass roll-off control in 2 dB steps:
from 0 to -8 dB
@35 Hz
Bass tilt control in 2 dB steps:
from 0 to -8 dB
@80 Hz
The 'CAL' position is with all tone controls set to
'off' and level control to maximum.
SYSTEM SPECIFICA
SYSTEM SPECIFICA
SYSTEM SPECIFICA
SYSTEM SPECIFICA
SYSTEM SPECIFICATIONS
TIONS
TIONS
TIONS
TIONS
Lower cut-off frequency, -3 dB:
<35 Hz
Upper cut-off frequency, -3 dB:
>50 kHz
Free field frequency response of system:
36 Hz - 48 kHz (±2.5 dB)
Maximum short term sine wave acoustic output on
axis in half space, averaged from 100 Hz to 3 kHz:
@1m
>111 dB SPL
@0.5m >117 dB SPL
Maximum long term RMS acoustic output in same
conditions with IEC-weighted noise (limited by
driver unit protection circuit):
@1m
>102 dB SPL
@0.5m >108 dB SPL
Maximum peak acoustic output per pair on top of
console, @ 1m from the engineer with music
material:
>122 dB
Self generated noise level in free field @ 1m on
axis:
<10 dB (A-weighted)
Harmonic distortion at 90 dB SPL at 1m on axis:
freq. <200 Hz
<2%
freq. >200 Hz
<1%
Drivers:
Bass
210 mm cone
Midrange
80 mm cone
Treble
9x65 mm
ribbon
Weight:
20 kg (44 lb)
Dimensions:
Height 495 mm
(19
1
/
2
")
Width 320 mm
(12
5
/
8
")
Depth 290 mm
(11
7
/
16
")
DIGIT
DIGIT
DIGIT
DIGIT
DIGITAL SECTION
AL SECTION
AL SECTION
AL SECTION
AL SECTION
Digital input :
XLR female
Digital thru output:
XLR male
Maximum input word length:
24 bits
Input format:
AES/EBU,
SP-DIF*
Input termination impedance:
110 Ohms*
Input sampling rate:
29-100 kHz (no de-emphasis)
44.1 kHz (using de-emphasis)
Jitter resiliance:
0.15 unit intervals
Dynamic range:
113dB (A weighted, triangular
PDF dither, 24 bit data)
De-emphasis:
50/15us, automatic
Recovered clock jitter:
200 picoseconds RMS typical
Output level for full scale digital input:
variable from 76 to 112 dB
SPL @1m
* An optional impedance matching adapter is
required for 75 Ohm signal source.
OPTIONS
OPTIONS
OPTIONS
OPTIONS
OPTIONS
Flight case
Order Code 1001-401
Wall mount
Order Code 1010-404-V/H*
Floor stand
Order Code 1010-405-V/H*
Grille
Order Code 1010-409
*V=Vertical (for S30D V), H=Horizontal (for S30D H)
