Genelec HT324AC, Operating Manual

Page: 6 / 6

Genelec Document D0071R001 Copyright Genelec Oy 2.2006. All data subject to change without prior notice
www.genelec.com
International enquiries:
Genelec, Olvitie 5
FIN-74100, Iisalmi, Finland
Phone +358 17 83881
Fax +358 17 812 267
Email genelec@genelec.com
In the U.S. please contact:
Genelec, Inc., 7 Tech Circle
Natick, MA 01760, USA
Phone +1 508 652 0900
Fax +1 508 652 0909
Email genelec.usa@genelec.com
In China please contact:
Genelec China Representative Office
Soho New Town, 88 Jianguo Road
D-1504, Chaoyang District
Beijing 100022, China
Phone +86 10 8580 2180 Fax +86 10 8580 2181
Email genelec.china@genelec.com
AMpLIfIER SEcTIoN
cRoSSovER SEcTIoN
SySTEM SpEcIfIcATIoNS
HT324AC Operating Manual
Fig 8: The above curves illustrate the effect of the 'bass tilt', 'bass roll-off'
and 'bass',' mid' and 'treble' level controls on the free field response,
measured at 2 m
Fig 9: The upper curve group shows the horizontal directivity
characteristics of the HT324AC in its horizontal configuration measured
at 29m. The lower curve is a 1/6 octave power response measurement,
derived from 144 directivity measurements..
Lower cut-off frequency, -3 dB:
≤
32 Hz
Upper cut-off frequency, -3 dB:
≥
20 kHz
Free field frequency response of system:
33 Hz - 20 kHz (± 2.5 dB)
Maximum short term sine wave acoustic output on
axis in half space, averaged from 100 Hz to 3 kHz
@ 1 m
≥ 123 dB SPL
Maximum long term RMS acoustic output in same
conditions with IEC-weighted noise (limited by
driver unit protection circuit)@ 1 m:
≥ 118 dB SPL
Maximum peak acoustic output per pair @ 2 m from
the engineer with music material:
≥
125 dB
Self generated noise level in free field @ 2 m on
axis:
≤
15 dB(A)
Harmonic distortion at 100 dB SPL @ 1m on axis:
Freq: 50...200 Hz <1%
200...10kHz <0.5%
Drivers:
Bass 2 x 305 mm (15") cone
Mid 1 x 130 mm (5") cone
Treble 1 x 25 mm (1") metal dome
Weight: Speaker 84 kg (185 lb)
Amplifier 30 kg (66 lb)
Speaker dimensions (Horizontal mounting):
Height 489 mm (19 1/4”)
Width 1210 mm (47 5/8”)
Depth 412 mm (16 1/8”)
*Amplifier dimensions:
Height 310 mm (12
3
/
16
")
Width 483 mm (19")
Depth 250 mm (9 13 /
16
")*
Bass amplifier output power with an 8
Ω
load:
Short term 2 x 400 W
Mid amplifier output power with a 8
Ω
load:
Short term 350 W
Treble amplifier output power with an 8
Ω
load:
Short term 120 W
Long term output power is limited by driver unit
protection circuitry.
Slew rate: 80 V/µs
Amplifier system distortion at nominal output:
THD
≤
0.05%
SMPTE-IM
≤
0.05%
CCIF-IM
≤
0.05%
DIM 100
≤
0.05%
Signal to Noise ratio, referred to full output:
Bass
≥
100 dB
Mid
≥
100 dB
Treble ≥ 100 dB
Mains voltage: 100/200 or 115/230V
Voltage operating range at
230V setting: 207 - 244 V (-10/+6 %)
115V setting: 104 - 122 V (-10/+6 %)
Power consumption:
Idle 70 W
Full output 1000 W
Input connector: XLR female pin 1 gnd
pin 2 +
pin 3 -
Input impedance: 10 kOhm
Ω
balanced
Input level for 100 dB SPL output @ 1m:
variable from +6 to -6 dBu
Input level for maximum short term output of 126 dB
SPL @ 1m:
variable from +32 to +20 dBu
Subsonic filter below 25 Hz : 18 dB/octave
Ultrasonic filter above 22 kHz: 12 dB/octave
Crossover frequencies:
Bass/Mid 400 Hz
Mid/Treble 3.2 kHz
Crossover acoustical slopes: >24 dB/octave
Level control operating range in 1 dB steps:
Bass from 0 to -6 dB & MUTE
Mid from 0 to -6 dB & MUTE
Treble from 0 to -6 dB & MUTE
Bass roll-off control in 2 dB steps:
from 0 to -8 dB @ 32 Hz
Bass tilt control operating range in 2 dB steps:
from 0 to -8 dB @ 50 Hz
The 'CAL' position is with all tone controls set to 'off'
and input sensitivity control to maximum and cor-
responds to a maximally flat free field response.