AIW25 Operating Manual
Genelec Document D0064R001. Copyright Genelec Oy 11.2006. All data subject to change without prior notice
www.genelec.com
International enquiries:
Genelec, Olvitie 5
FIN-74100, Iisalmi, Finland
Phone +358 17 83881
Fax +358 17 812 267
Email [email protected]
In the U.S. please contact:
Genelec, Inc., 7 Tech Circle
Natick, MA 01760, USA
Phone +1 508 652 0900
Fax +1 508 652 0909
Email [email protected]
In Sweden please contact
Genelec Sverige
Ellipsvägen 10B
P.O. Box 5521, S-141 05 Huddinge
Phone +46 8 449 5220
Fax +46 8 708 7071
Email [email protected]
In China please contact:
Beijing Genelec Audio Co. Ltd.
Jianwai SOHO, Tower 12, Room 2306
39 East 3rd Ring Road
Chaoyang District
Beijing 100022, China
Phone +86 0 5869 7915, Fax +86 10 5869 7914
AmplIfIeR SectIoN
SyStem SpecIfIcAtIoNS
AIW25
Lower cut-off frequency, –3 dB
≤
68 Hz
Upper cut-off frequency, –3 dB
> 20 kHz
Free field frequency response
70 Hz – 18 kHz (± 2.5 dB)
Maximum short term sine wave acoustic
output on axis in half space, averaged from
100 Hz to 3 kHz
@ 1 m > 100 dB SPL
Maximum peak acoustic output per pair with
music material
@ 1 m > 110 dB SPL
Self generated noise level in half space at 1 m
on axis (A-weighted)
≤
10 dB
Harmonic distortion at 85 dB SPL
at 1 m on axis
Freq:
70…200 Hz
> 200 Hz
< 3%
< 0.5 %
Drivers
Bass
Treble
130 mm (5") cone
19 mm (
3
/
4
") metal dome
Weight
Loudspeaker cabinet
Amplifier
3.7 kg (8.1 lb)
2.2 kg (4.8 lb)
Dimensions
Loudspeaker cabinet max. height
Loudspeaker cabinet max. width
Loudspeaker cabinet max. depth
Cutout height
Cutout width
Minimum free depth measured from the
surface of the wall
Amplifier height
Amplifier width
Amplifier depth*
*Note that the cable connectors require at
least 100 mm (4”) of space behind the
amplifier
360 mm (14
3
/
16
”)
267 mm (10
1
/
2
”)
104 mm (4
3
/
32
”)
334 mm (13
5
/
32
”)
240 mm (9
7
/
16
”)
98 mm (3
27
/
32
”)
177 mm (6
31
/
32
”) (4U)
54 mm (2
1
/
8
”)
260 mm (10
1
/
4
”)
AIW25
Bass amplifier short term output power
Treble amplifier short term output power
(Long term output power is limited by driver
unit protection circuitry)
40 W at 8 Ohm load
40 W at 8 Ohm load
Amplifier system THD at nominal output
≤
0.08 %
Mains voltage
100, 120 or 230 V
Power consumption (average)
Idle
Full output
10 VA
80 VA
Recommended loudspeaker cable gauge
0.8 to 5.0 mm
2
(18 to 10 AWG)
Standby/On switching by signal sensing Autostart function or +12 V DC
remote control
cRoSSoVeR SectIoN
AIW25
Connectors:
XLR female input, balanced 10 kOhm
RCA female input, unbalanced 10 kOhm
“LINK OUT” XLR male output, balanced
10 kOhm
pin 1 gnd, pin 2 +, pin 3 -
pin +, ring gnd
pin 1 gnd, pin 2 +, pin 3 -
Input level for 100 dB SPL output at 1 m
-6 dBu
Input Sensitivity adjustment range
+6 dBu to -6 dBu
Crossover frequency, Bass/Treble
3.0 kHz
Treble Tilt control operating range
0 to –2 dB @ 15 kHz
Bass Tilt control operating range in –2 dB
steps
From 0 to -6 dB @ 100 Hz
Bass Roll-Off control
-6 dB @ 85 Hz
The ‘CAL’ position is with all tone controls set to ‘off’ and the input sensitivity
control to maximum (fully clockwise).
Figure 7. The main dimensions of the AIW25 loudspeaker cabinet
Figure 8. The main dimensions of the RAM2 amplifier
