Genelec 7350APM Operating Manual Download Page 4

7350A Operating Manual

Genelec Document D0116R002 Copyright Genelec Oy 9.2014. All data subject to change without prior notice

www.genelec.com

International enquiries: 
Genelec, Olvitie 5
FIN-74100, Iisalmi, Finland
Phone +358 17 83881

Fax +358 17 812 267

Email [email protected]

In the U.S. please contact: 
Genelec, Inc., 7 Tech Circle
Natick, MA 01760, USA
Phone +1 508 652 0900

Fax +1 508 652 0909

Email [email protected]

In China please contact: 
Beijing Genelec Audio Co, Ltd
Room 101, 1st Floor Building 71 B33
Universal Business Park 
No.10 Jiuxianqiao Road,Chaoyang District, 
Beijing 100015, China
Phone +86 (10) 5823 2014, Post code 100015
Email [email protected]

AMPLIFIER SECTION

CONNECTIONS

SIGNAL PROCESSING

SYSTEM SPECIFICATIONS

7350A

Free field frequency response 

± 3 dB 
-6 dB

 
25 - 150 Hz
22 - 160 Hz

Maximum short term sine wave SPL output 
averaged from 30 to 85 Hz, measured in half 
space at 1 meter

   > 104 dB

Self generated noise level in half space at 1 m 
on axis (A-weighted)

< 5 dB

Harmonic distortion at 90 dB SPL 
at 1 m on axis in half space  30… 85 Hz

2nd 

 

3rd 

< 4 % 
< 1 %

Driver, magnetically shielded

205 mm (8")

Weight

19 kg (42 lbs)

Dimensions   

Height
Width
Depth

410 mm (16

1

/

8

 in) 

350 mm (13

3

/

4

 in) 

319 mm (12

9

/

16

 in)

7350A

Subsonic filter (18 dB/octave) below

20 Hz

LFE cutoff frequency

150 Hz

Midband rejection >400 Hz

 50 dB

GLM software Auto Cal tools

Parametric notch filters 
Delay adjustment 
Level adjustment

 
20 
160 ms 
60 dB

7350A

Amplifier short term output power
(Long term output power is limited by driver 
unit protection circuitry)

150 W

Amplifier system THD at nominal output

< 0.005%

Mains voltage

100, 120 or 230 V

Power consumption (average)

Standby (ISS active)
Idle
Full output

 
< 0.5 W 
8.5 W 
150 W

ANALOG

7350A

Input / Output connectors XLR female / male
LFE Input connector XLR female

5 / 5
1

Pin sequence

pin 1 
pin 2 
pin 3

gnd
+ (non-inverting)
- (inverting)

Input impedance

10 kohm balanced

Input level for 100 dB SPL output @ 1 m

-6 dBu  
(variable in GLM software)

Output gain

0 dB

The output connectors carry an unfiltered copy of the signal arriving into 
their respective Input connectors.

DIGITAL

7350A

Input / Output connectors XLR female / male

1 / 1

Signal format

AES/EBU single wire

Digital audio

Word length
Sample rate

 
16 - 24 bits
32 - 192 kHz

GLM NETWORK

7350A

Input / Output RJ45

1 / 1

In Sweden please contact 

Genelec Sverige

Ellipsvägen 10B

P.O. Box 5521, S-141 05 Huddinge

Phone +46 8 449 5220

Fax +46 8 708 7071

Email [email protected]

Compliance with FCC rules

This device complies with part 15 of the FCC Rules. Operation is subject to the following 
two conditions: 

This device may not cause harmful interference, and this device must accept any inter-

ference received, including interference that may cause undesired operation. 

Note: This equipment has been tested and found to comply with the limits for a Class B 

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, if not installed and used 
in accordance with the instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not occur in a particular instal-
lation. If this equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is encouraged to 
try to correct the interference by one or more of the following measures: 

• 

Reorient or relocate the receiving antenna. 

• 

Increase the separation between the equipment and receiver. 

• 

Connect the equipment into an outlet on a circuit different from that to  

 

which the receiver is connected. 

• 

Consult the dealer or an experienced radio/TV technician for help

Modifications not expressly approved by the manufacturer could void the user’s author-

ity to operate the equipment under FCC rules.

Reviews: