Gemtek Systems WL-299 series User Manual Download

Page: 18 / 20

6 Technical Specifications of Wireless Ethernet Adapter

Standards supported

−

IEEE 802.11 standard for Wireless LAN

−

All major networking standards (including IP, IPX)

Environmental

Operating temperature (ambient):

−

-10 ~ 50°C

Humidity:

−

Max. 95% Non-condensing

Power specifications

DC power supply

−

Input : DC 100-240 50-60 Hz 2A

−

Output: 5V DC 2A converter incl.

Radio specifications

Range:

−

per cell indoors approx. 35-75 meters

−

per cell outdoors up to 100-250 meters

Transmit power:

−

Nominal Temp Range: 14 dBm, 12min.

Frequency range:

−

2.4-2.4835 GHz, direct sequence spread spectrum

Number of Channels:

−

Most European countries: 13 (1-13)

−

US and Canada: 11 (1-11) (3 non-overlapping)

−

France: 4 (10-13) (1 non-overlapping)

−

Japan : 14 (1-14)

Specific features

Supported bit rates:

−

11 Mbps : CCK

−

5.5 Mbps : CCK

−

1 Mbps : DBSK

Summary of Contents for WL-299 series





















Search results

Summary of Contents for WL-299 series

Reviews:

Related manuals for WL-299 series

Brands by name

Popular brands

Gemtek Systems WL-299 series, User Manual

Search results

Summary of Contents for WL-299 series

Reviews:

Related manuals for WL-299 series

Brands by name

Popular brands