Use the Toggle switch for
CH 1
to
CH 2 (16)
to assign the
CH
(s)
to be monitored in your headphones.
Use the face panel located rotary
CUE VOLUME CONTROL
(17) to adjust the
CUE
volume without changing the overall mix.
By turning the face panel located
CUE/MIX/PGM ROTARY
CONTROL
(18) counter clockwise you will be able to monitor
the assigned cue signal. Slowly turning the control clockwise to
middle position allows you to monitor
CUE MIX
with
PGM
.
Moving the control clockwise to the right allows you to monitor
PGM (Main)
output.
6.
CROSS FADER SECTION:
The
CROSS FADER
(19) allows
you to mix from one source to another. The
CROSS FADER
(19)
in your unit is removable and if the need arises can be easily
replaced. Your
Gemini
mixer comes with an
RG-45
(
RAIL
GLIDE™
)
DUAL-RAIL CROSS FADER
, which has internal dual
stainless steel rails that allow the slider to ride smoothly and
accurately from end to end, and a special mix curve. There are
also
CURVE and REVERSE
controls (20) controls located on
the front panel for adjusting the speed in which the audio comes
in on each side of the crossfader and the direction each channel
comes in from. Also available is our
RG-45 Pro
(
RAIL GLIDE
Pro™
)
DUAL-RAIL CROSS FADER
. This unique
CROSS
FADER
features, a lighter feel and smoother curve specially
made for scratching. Just purchase one from your
Gemini
deal-
er and follow the instructions:
NOTE: DO NOT APPLY PRESSURE WHILE
USING THE CROSS FADER (46). LIGHTLY GLIDE THE CROSSFADER BACK
AND FORTH. PRESSING DOWN ON THE CONTROLS CAN BEND CONTACTS
AND CAUSE A LOSS OF SOUND.
7.
OUTPUT SELECTION CONTROL:
Once you are comfort-
able with the sound level of your music you may adjust the vol-
ume with the
MASTER
(21) rotary control.
8.
MIC SECTION:
Plug your main
MIC
into the
MIC 1/4"
input
(6) located on the rear panel. You can use the
Mic Gain Control
(22) as well as the HIGH (23) and LOW (24) controls to adjust
the volume and tone of the microphone signal
9.
VU METER:
The
PS-424x
has a dual mode
VU METER
(25)
that allows you to monitor the decibel levels of
CUE
and
PGM
or
LEFT
and
RIGHT
stereo levels of the
MASTER
output. With the
VU MODE SWITCH
(26) you may monitor the output level of the
CUE
and
PGM
when the switch is
UP
. When this mode is
engaged the
CUE
will be located on the left of the
VU METER
,
while the
PGM
will be located on the
RIGHT
. Or you can moni-
tor the
LEFT
and
RIGHT
stereo decibel levels of the
MASTER
OUTPUT
when the switch is in the
DOWN
position.
10.
”Ipod Friendly” cable:
To connect your Ipod or other Digital
Media Player, use the included Ipod cable. Connect the 1/8’’ end
of the cable to the headphone or line out jack of your player, and
connect the RCA end to the line input (7) of your mixer.
INPUTS:
Phono..................................................................3 mV, 47 KOhm
Line.................................................................150 mV, 27 KOhm
MIC…………..........……….................1.5 mV, 1 KOhm Balanced
OUTPUTS:
Max.................................................................20V Peak-to-Peak
Rec....................................................................225 mV, 5 KOhm
GENERAL:
Frequency Response................................20Hz - 20KHz +/- 2 dB
Distortion.........................................................................< 0.02%
S/N Ratio.........................................................Better Than 85 dB
Headphone Impedance...................................................16 Ohm
Power Source (external)...........................115 V, 50 Hz, 15 W
Unit Dimensions..............................................10" x 3.3" x 11.9"
…………………………………………….....(254 x 84 x 303 mm)
Weight...............................................................6.93 lbs (3.15 kg)
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTIFICATION FOR
IMPROVEMENT.
SPECIFICATIONS:
REPLACEABLE CROSS FADER
1. UNSCREW THE OUTSIDE FACE PLATE SCREWS ON THE LOWER HALF OF
THE MIXER. REMOVE THE FADER CAPS AND FACE PLATE.
2.UNSCREW THE FADER (B)
SCREWS. DO NOT TOUCH INSIDE
SCREWS
(C).
CAREFULLY
REMOVE OLD CROSS FADER AND
UNPLUG CABLE (D).
3. PLUG IN THE NEW CROSS
FADER INTO CABLE (D) AND
PLACE BACK INTO MIXER.
4. SCREW THE CROSS FADER TO
MIXER WITH THE FADER PLATE
SCREWS (B).
5. REPLACE THE LOWER HALF
FACE PLATE AND SCREW TO THE
MIXER.
Summary of Contents for PS-424x
Page 3: ... 2 PS 424x ...
