9.
CROSSFADER SECTION:
The
CROSSFADER
(38)
allows you to mix from one source to another. The
CH 2
(28) is controlled on the
LEFT
side of the
CROSSFADER
(38).
CH 3
(31) is controlled by the
RIGHT
side of the
CROSSFADER
(38).
CH 1
(25) and
CH 4
(34) are con-
trolled through their respective
SLIDE CONTROLS
(25,
34) and not the
CROSSFADER
(38). The
CROSSFADER
(38) in your unit is removable and if the need arises can
be easily replaced. Your Gemini mixer comes with an
RG-
45 PRO (RAILGLIDE™) Dual-Rail Crossfader
.
Rail
Glide™
crossfaders have internal dual stainless steel
rails that allow the slider to ride smoothly and accurately
from end to end. Also available is our
CF-45 PRO
(PROGLIDE™) Dual-Rail Crossfader
. This unique
crossfader features, state of the art conductive plastic
technology, for unlimited useage. Another crossfader we
have available is the
PSF-45 (PRO SCRATCH™) cross-
fader
with a special curve designed for scratch mixing.
Just purchase one from your Gemini dealer and follow the
instructions:
10.
MIC SECTION:
Plug your main mic into the
MIC 1 XLR
INPUT
(15) located on the top panel. The rotary controls
for
HIGH
(18) and
LOW
(19) for
MIC 1
(15) allow you to
adjust the tone of
MIC 1
(15). The
MIC 1 ROTARY VOL-
UME CONTROL
(17) above the
HIGH
(18)
/LOW
(19) con-
trols adjust the decibel level of
MIC 1
(15). You may also
plug a second mic into the rear panel at the
MIC 2 ¼"
JACK
(14). The tone and decibel level of
MIC 2
(14) is
controlled by the
CH 1 SLIDE
(25) and the
5 BAND EQ
(35).
11.
TALKOVER:
The purpose of the
TALKOVER MODE
is
to allow the program playing to be muted so that the mic
may be heard above the music. The
MIC/TALKOVER
SWITCH
(16) controls
MIC 1
(15) with
3
settings:
- When the
MIC/TALKOVER SWITCH
(16) is in the
BOT-
TOM
position,
MIC 1
(15) and
TALKOVER MODE
are all
OFF
.
- When the
MIC/TALKOVER SWITCH
(16) is in the
CEN-
TER
position,
MIC 1
(15) is
ON
and
TALKOVER MODE
is
OFF
. The
MIC ON LED INDICATOR
glows when
MIC
1 (15)
is
ON
.
- When the
MIC/TALKOVER SWITCH
(16) is in the
TOP
position,
MIC 1
(15) is
ON
and
TALKOVER MODE
is
ON
,
and the volume of all sources except
MIC 1
(15) inputs is
lowered by -16 dB.
12.
VU METER:
The
VU METER
(37) indicates the pro-
gram output level of the
MASTER
(2) left and right stereo
levels.
SPECIFICATIONS:
INPUTS:
MIC 1..............................................1.5mV 1kOhm Balanced
MIC 2.............................................1.5mV 1KOhm Balanced
Phono.............................................................3 mV 47kOhm
Line.............................................................150 mV 10kOhm
OUTPUTS:
Amp............................................................0 dB 1V 400Ohm
Max...........................................................20V Peak to Peak
Rec................................................................225mV 5kOhm
GENERAL:
5 Band EQ..................................................................± 12dB
Frequency Response.........................20Hz - 20KHz +/- 2dB
Distortion....................................................Less Than 0.02%
S/N Ratio...................................................Better Than 80dB
Talkover Attenuation.....................................................-16dB
Power Source.............................Adapter-115V/15V AC 0.5A
................................................................ 230V/15V AC 0.5A
Unit Dimensions...................................W 19" x H 3.4" x D 7"
...............................................................(483 x 76 x 178mm)
Weight........................................................7.04 lbs (3.19 kg)
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTIFICATION
FOR IMPROVEMENT.
Replaceable Crossfader
1. Unscrew the outside
FADER
plate screws (B).
- Do not touch
INSIDE SCREWS
(C).
2. Carefully remove old
Crossfader and unplug
CABLE
(D).
3.Plug new Crossfader into
CABLE
(D) and place
back into mixer.
4. Screw Crossfader to
mixer with the
FADER
PLATE SCREWS
(B).
(5)
Summary of Contents for MM-01
Page 3: ... 3 ...