manualshive.com logo in svg

Gemini GEM-DXRP3, Operating Manual

Share
Download
Gemini GEM-DXRP3 Operating Manual Download Page 11

11 

F I R E   P R O T E C T I O N  

(Applicable only where local ordinance permits use of this alarm control panel for fire protection). 

Fire-Zone Alarm 

If a fire is detected, the FIRE/TBL light will display with the zone number and the 

keypad sounder will pulse. 

•

If a fire is in progress, evacuate the premises immediately!  If necessary, call 
the Fire Department from an outside phone. 

•

If there is no evidence of a fire, enter your code and press 

v

 to silence the 

alarm. 

•

Check the smoke detector(s).  If a smoke detector tripped, its red alarm 
indicator light will be on. 

•

After the alarm condition is corrected (thermostat cooled down; smoke cleared 
from detector; etc.), pressing 

y

 again will reset the keypad within about 10 

seconds. 

 

F

ire-Zone Trouble

 

•

The system is constantly monitoring the Fire Zone(s) to insure they are in good 
working order.  

•

If a problem on a Fire Zone is detected, a system trouble E41 will display, 
followed by the number of the Fire Zone in trouble.  The sounder will activate, the 
SYS TBL light will come on and the FIRE/TBL light will blink.  

•

Press the 

y

 button to silence the sounder.  Call for service immediately! 

   

NN 

INTERIOR  BYPASS  FIRE/TBL  SYS TBL 

CHIME 

   

NN 

INTERIOR  BYPASS  FIRE/TBL  SYS TBL 

CHIME 

   

41 

INTERIOR  BYPASS  FIRE/TBL  SYS TBL 

CHIME 

   

E 

INTERIOR  BYPASS  FIRE/TBL  SYS TBL 

CHIME 

Summary of Contents for GEM-DXRP3

































Reviews:

No comments

Brands by name

Popular brands

Load more brands