PITCH BEND mode the JOG WHEEL will function the same
as the PITCH BEND allowing you to speed up (FORWARD)
or slow down (REWIND) the music clockwise being (FOR-
WARD) and counter clockwise being (REWIND).
JOG MODE BUTTON: When the JOG MODE BUTTON is il-
luminated it indicates the JOG WHEEL is in SEARCH MODE,
and when not illuminated it indicates that the JOG WHEEL is
in PITCH BEND MODE.
DISPLAY: The DISPLAY shows the track number, pitch val-
ue, pitch bend, single, continue (for continuous play), play/
pause modes, fast forward/reverse modes, loop mode, re-
loop mode, PGM, repeat modes, the playback display bar,
and three different time displays. These times displays are
TIME ELAPSED on the track, TIME REMAINING on the disc
and TIME REMAINING on the track. Time is measured in
minutes, seconds and frames.
PGM: Allows you to create a set playlist. To program a set
list into the CDM-3200 memory, begin by stopping the unit
from play and pressing PGM to begin the set list. Select a
track by using the track selection button to scan to the first
track to be placed in the set list. When you have selected the
proper track press PGM and the CDM-3200 will be ready to
set your next selection. Repeat the previous steps until you
have completed your play list, then press play to begin the
set list.
SINGLE: Pressing the SINGLE button engages SINGLE
mode, in this mode the CDM-3200 will play one song and
then stop. Pressing the SINGLE button again will then acti-
vate CONTINUOUS mode causing the unit to play continu-
ously (after the last track, the unit will return to the first track
of the disc and continue to play).
TIME: The TIME button switches the time display between
three available sources, these three are TIME ELAPSED on
the track, TOTAL REMAIN on the disc and REMAIN on the
track. TIME ELAPSED indicates how much time has cur-
rently gone by since the play button was pressed, TOTAL
REMAIN will count down the time remaining on the entire
disc and REMAIN counts down the time that is left before the
end of the track.
PITCH: Hold the PITCH button to activate the PITCH CON-
TROL SLIDE. Pitch ranges can be controlled through the
use of the PITCH CONTROL SLIDER. Hold the PITCH but-
ton again to deactivate this mode.
PITCH CONTROL SLIDE: Moving the PITCH CONTROL
SLIDE up or down will change the pitch percentage +/ -
12%.
PITCH BEND: Pushing the PITCH BEND BUTTONS will au-
tomatically raise the pitch up to +16% or lower the pitch down
to -16% from the existing pitch setting. Releasing the buttons
will return the pitch to the original pitch setting. You can use
this function to match the beat when mixing from one song to
another.
LOOP SECTION: A LOOP repeats the section between the en-
try point (IN) and the exit point (OUT).
A. To set a loop while the unit is playing, start by pressing
the IN BUTTON (it will light up)
B. When you reach the desired end loop point press the
OUT BUTTON (it will also light up). The loop will continue
playing until you press the OUT BUTTON again allowing
the music to continue from that point on.
C. To re-engage the loop you must press the RELOOP
BUTTON.
D. When you have released your loop the OUT BUTTON
will turn OFF and the IN BUTTON will remain lit to indicate
that your loop is stored in the CDM-3200 memory.
E. Pressing the IN BUTTON again while the unit is playing
will erase the previously saved loop while saving your new
loop entry point.
F. Press OUT to exit the loop and save a new complete
loop.
G. Press RELOOP to return to the beginning of the previ-
ously saved loop from normal play. Press RELOOP repeat-
edly to cause the loop to stutter.
NOTE: THE FIRST LOOP WILL HAVE A PAUSE AT THE EXIT
POINT, WHILE ALL OTHERS WILL BE SEAMLESS.
PLAY / PAUSE: Each press of the PLAY / PAUSE BUTTON
causes the operation to change from PLAY to PAUSE or from
PAUSE back to PLAY. The PLAY/PAUSE BUTTON remains lit
when in PLAY mode, while it blinks in PAUSE mode.
CUE: While the unit is playing and after the cue point has been
programmed, pressing CUE will cause the CD player to en-
ter the PAUSE mode (PLAY/PAUSE BUTTON blinks) at the
programmed cue point (the CUE LED is lit). Holding down the
CUE button changes the function to preview, and allows you to
stutter start or play from the programmed CUE POINT. Releas-
ing the CUE button will return the CD to the preset CUE point.
TRACK SELECTION: The TRACK SELECTION buttons let
you select the track to play. +10 allows you to scan through the
track selection in increments of 10. TRACK SKIP allows you to
scan through each track one at a time. Select the track desired
by pressing the TRACK SELECTION BUTTON.
NOTE: ONCE YOU HAVE SKIPPED TO ANOTHER TRACK,
YOU MAY NOT GO BACK TO YOUR PROGRAMMED CUE
POINT. YOU MUST BEGIN YOUR CUE SELECTION OVER
AGAIN, THE CUE WILL BE PRESET TO THE BEGIN-NING
OF THE NEWLY SELECTED TRACK.
5
CDM-3200
11
12
13
14
16
15
17
18
19
20
21
22
