Gemini 932 Series Installation And Use Manual Download Page 15

Page: 15 / 18

To carry out the operation successfully, make sure the required electrical connections

(bonnet switch and ignition) are complete.

All previously programmed

can be deleted.

To clear memory proceed as follows.

With the system disarmed, open the bonnet and leave it open

devices

!
!
!

Turn ignition key “ON-OFF”-“ON-OFF-ON”-“OFF-ON”.
After the 4th rotation, leave it “ON”.

Close the bonnet.

To confirm it has entered in the delete mode, the system gives 2 acoustic signals (1 high and 1 low-
pitched), the turn indicators flash once and the LED turns ON

To clear the memory, leave the bonnet closed for at least 8 seconds

The following operations must be carried out within 4 seconds otherwise the procedure

is invalidated.

If the bonnet is opened before 8 seconds, the devices will not be

deleted.

!
!

”.

The status LED turns OFF when the devices are deleted
Turn ignition key “OFF

he end of the procedure.

One long low-pitched acoustic signal will confirm t

14.0 - DELETING PROGRAMMED DEVICES

INSTALLER MANUAL - PAGE 15

Summary of Contents for 932 Series



















Search results

Summary of Contents for 932 Series

Reviews:

Related manuals for 932 Series

Brands by name

Popular brands

Gemini 932 Series, Installation And Use Manual

Search results

Summary of Contents for 932 Series

Reviews:

Related manuals for 932 Series

Brands by name

Popular brands