background image

 

 

Designed

 

and

 

manufactured

 

by

 

GEMINI

 

TECHNOLOGIES

 

srl

 ‐  

Via

 

L.

 

Galvani,

 

12

 

 

21020

 

Bodio

 

Lomnago

 

(VA)

 

 

Italy

 

Tel.

 

+39

 

0332

 

943211

 

 

Fax

 

+39

 

0332

 

948080

 

 

www.gemini

alarm.com

 

ISO

 

9001

 

CERTIFIED

 

COMPANY

 

 

Rev.00

  

03/2017

 

 

 

6/9 

 
 
 
 
 
 
 
 

 

 

 

 

System configuration with the parameters detailed in par.12.0 is done by pressing buttons “A” and “B” on the buzzer (see figure below).  

 

Press button “A” to select the parameter to configure.  

 

Press button “B” to select the desired setting.      

11.1 - HOW TO ENTER IN PROGRAMMING MODE:

 

 

1.

 

Turn ignition “ON”. 

2.

 

Simultaneously press buttons “A” and “B” for approx 4 sec. 

3.

 

Operation will be confirmed by 1 Beep and 1 Red/Green LED flash. 

4.

 

Wait until the LED turns OFF. 
 
 

11.2 - PARAMETER SETUP: 

 

1.

 

Within 10 sec. after the LED turns OFF, press button “A” the number of times corresponding to the parameter to customize. At each button press there will be 1 

Beep and 1 Red LED blink. 

 

2.

 

Press button “B” the number of times corresponding to the desired setup. At each button press there will be 1 Beep and 1 Green LED blink. 

Example: To set the maximum detection distance of the inner sensors at 80 cm => press button “A” twice and then button “B” 9 times. 

 
 

11.3 - SETUP CONFIRMATION

:  

 

1.

 

The buzzer will repeat the number of Beeps and blinks corresponding to the selected setup. After a few seconds, if the code has been successfully programmed, the 

buzzer will give off a ‘Jingle’. Proceed with another setup. 

 

2.

 

In case of an incorrect entry, a low tone signal (Bop) will sound. Re-enter the desired code. 

 

Turn ignition OFF and then back ON to transfer the new parameters from the buzzer to the control unit. The LED on the ON/OFF switch will blink during data transfer (data 
transfer timeout: 20 sec. max). A ‘Jingle’ will confirm data has been successfully transfered otherwise a Bop will sound. In this case, turn ignition OFF and then back ON to 
repeat data transfer. The next time ignition will be turned ON, the system will operate according to the configured parameters. 

 

11.4 - RESTORE FACTORY SETTINGS

 

 

1.

 

Simultaneously press and hold buttons “A” and “B”; turn ignition ON.  

2.

 

When the buzzer gives off a Beep, release buttons “A” and “B”.  

3.

 

The LED will start blinking Red/Green. 

4.

 

When the LED stops blinking, a Jingle” will confirm the buzzer has been reset to the original factory settings.  

5.

 

Turn ignition OFF and then back ON to transfer parameters from the buzzer to the control unit. The LED on the ON/OFF switch will blink during data transfer (data 

transfer timeout: 20 sec. max). A Beep will confirm data has been successfully transfered otherwise a Bop will sound. In this case, turn ignition OFF and then back 

ON to repeat data transfer. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Before configuring the system, ensure all connections have been done properly. 

 

Parameters must only be configured by qualified personnel. 

 

11.0 - PARAMETER SET-UP 

 

Button 

A

 

Button

LED

 

Summary of Contents for 514F










Reviews: