Gemalto Cinterion PLS62T-W USB Hardware Interface Description Download Page 34 | Manualshive

Page: 34 / 91

background image

Cinterion

®

Java Terminal Hardware Interface Description

3.9 Power Supply

40



PLS62T-W_HID_v01

2018-06-20

Confidential / Prelimenary

Page 34 of 91

3.9

Power Supply

The Java Terminal power supply via Western jack has to be a single voltage source of
V

PLUS

=8V…30V capable of providing a peak current (pulsed 2x577ms at T=4.615ms) of about

1.2A at 8V during an active transmission

1

. The uplink burst causes strong ripple (drop) on the

power lines. The drop voltage should not exceed 1V. The absolute minimum voltage during
drops is given in

.

The Java Terminal are protected from supply voltage reversal. An external fast acting fuse
>0.4A with melting integral I

2

t (0.15 … 0.25)A

2

s is necessary to use the Java Terminal at a 12V

or 24V unlimited power supply system.

The power supply must be compliant with the EN60950 guidelines. A switching regulator reg-
ulates the input voltage for the internal supply.

When power fails for >1ms, Java Terminal reset or switch off. The watchdog can be configured
to restart the Java Terminal. When power fails for >15s the RTC will be reset.

Figure 9:

6-pole Western jack for power supply, ignition, reset, typical connection

1. As an alternative to the power supply via Western jack, Power over Ethernet (PoE) can be employed.

The PoE feature complies with IEEE 802.3 standards, and can be made available in Ethernet networks
via PoE enabled devices such as PoE routers or injectors.

Table 15:

Female 6-pole Western plug for power supply, ignition, power down

Pin

Signal name

Use

Parameters

1

PLUS

Power supply

8V – 30V DC (PLS62T-W USB)
8V – 57V DC (PLS62T-W LAN)

2

PLUS

Power supply

8V – 30V DC (PLS62T-W USB)
8V – 57V DC (PLS62T-W LAN)

3

RST_IN

Signal for module reset

U

IH

> 8V for t>10ms resets the terminal.

U

IL

<2V and low level for normal operation.

4

IGT_IN

Ignition

U

IH

>8V

Ignition >8V for more than 200ms switches
the Java Terminal on. Ignition is activated
only by a rising edge. The rise time is
<20ms

5

GND

Ground

0V

6

GND

Ground

0V

Pin assignmment and typical connection:

1 PLUS
2 PLUS
3 RST_IN
4 IGT_IN
5 GND
6 GND

V

PLUS

DC

6 5 4 3 2 1

«
...
32
33
34
35
36
...
»

Summary of Contents for Cinterion PLS62T-W USB




























































































Reviews:

No comments

Related manuals for Cinterion PLS62T-W USB

Brand: Yamaha Pages: 50

Brand: A&D Pages: 30

Brand: HABYS Pages: 16

Brand: Idex Pages: 141

Brand: IDEAL Networks Pages: 8

Brand: IDEAL Networks Pages: 5

Brand: Nectar Pages: 46

Brand: Neauvia Pages: 17

Brand: Park House Healthcare Pages: 12

Brand: Vapotherm Pages: 32

Brand: Vanguard Instruments Pages: 47

Brand: ValueStore US Pages: 2

Brand: ZAMST Pages: 14

Brand: Future Artist Pages: 42

Brand: ultraMEDIC Pages: 28

Brand: Evermed Pages: 16

Brand: Enerpac Pages: 36

NOVACAT X8 COLL

Brand: Pottinger Pages: 91

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands