manualshive.com logo in svg

Gemalto Cinterion EMS31-V, Hardware Interface Overview

Share
Download
Gemalto Cinterion EMS31-V Hardware Interface Overview Download Page 12

Cinterion

®

 EMS31-V Hardware Interface Overview

2.1 Application Interface

18

EMS31_V_HIO_v00.004

2018-02-27

Confidential / Preliminary

Page 12 of 35

The figure below shows a circuit to connect an external SIM card holder.

Figure 4:  

External UICC/SIM/USIM card holder circuit

The total cable length between the SMT application interface pads on EMS31-V and the pads 
of the external SIM card holder must not exceed 100mm in order to meet the specifications of 
3GPP TS 51.010-1 and to satisfy the requirements of EMC compliance.

To avoid possible cross-talk from the CCCLKx signal to the CCIOx signal be careful that both 
lines are not placed closely next to each other. A useful approach is using a GND line to shield 
the CCIOx line from the CCCLKx line.

SIM

CCVCC

CCRST

CCIO

CCCLK

220nF

1nF

CCIN

V180

R 220k

Switch position  (SIM inserted )

Switch position (SIM 

not inserted)

4k7

Summary of Contents for Cinterion EMS31-V




































Reviews:

No comments

Brands by name

Popular brands

Load more brands