Gemalto Cinterion ELS31T-J Hardware Interface Description Download Page 57

Page: 57 / 102

Cinterion

LTE Terminals Hardware Interface Description

4.5 Antenna Interface



ELSxT_HID_v04

2018-09-04

Confidential / Preliminary

Page 57 of 102

4.5

Antenna Interface

Table 26

lists RF antenna interface specifications for the LTE Terminals. Please note that the

specified conditions may not apply to or be supported by all terminals.

Table 26:

RF Antenna interface GSM / UMTS / LTE

Parameter

Conditions

Min.

Typical Max.

Unit

LTE connectivity

Band 1, 2, 3, 4, 5, 8, 12, 13, 18, 19, 20, 28 (not every module variant

supports all bands)

Receiver Input Sensitivity @

ARP, dual antenna (main+

diversity)

LTE 700 Band 12 (ch. band-

width 5MHz)

-99

dBm

LTE 700 Band 13 (ch. band-

width 5MHz)

-99.3

-101

dBm

LTE 700 Band 28 (ch. band-

width 5MHz)

-98.5

dBm

LTE 800 Band 20(ch. band-

width 5MHz)

-97

dBm

LTE 850 Band 5 (ch. band-

width 10MHz)

-98

dBm

LTE 850 Band 18 (ch. band-
width 5MHz)

-99.3

-103

dBm

LTE 850 Band 19 (ch. band-

width 5MHz)

-99.3

-103

dBm

LTE 900 Band 8 (ch. band-

width 5MHz)

-97

dBm

LTE AWS Band 4 (ch. band-

width 10MHz)

-100

dBm

LTE 1800 Band 3 (ch. band-

width 5MHz)

-97

dBm

LTE 1900 Band 2 (ch. band-

width 10MHz)

-100

dBm

LTE 2100 Band 1 (ch. band-

width 5MHz)

-100

dBm

RF Power @ ARP with 50

Ω

Load (power supply: 3.8/4V,

temperature 25°C)

LTE 700 Band 12 (ch. band-

width 5MHz; 1RB, position

low)

+23

dBm

LTE 700 Band 13

+23

dBm

LTE 700 Band 28

+23

dBm

LTE 800 Band 20

+23

dBm

LTE 850 Band 5 (ch. band-

width 5MHz; 1RB, position

low)

+23

dBm

LTE 850 Band 18

+23

dBm

LTE 850 Band 19

+23

dBm

LTE 900 Band 8

+23

dBm

Summary of Contents for Cinterion ELS31T-J







































































































Search results

Summary of Contents for Cinterion ELS31T-J

Reviews:

Gemalto Cinterion ELS31T-J, Hardware Interface Description, Page: 57 / 102

Search results

Summary of Contents for Cinterion ELS31T-J

Reviews: