manualshive.com logo in svg

Gemalto CINTERION BGS2T, At Command Set

The Gemalto CINTERION BGS2T is a cutting-edge GSM/GPRS wireless module. Our comprehensive user manual, complete with an extensive AT Command Set, is available for free download on our website. Discover the full potential of this product by accessing the manual at manualshive.com.

Share
Download
background image

BGS2T AT Command Set  

16.4 AT+CPBW

BGS2T_ATC_V01.301

Page 492 of 554

1/31/12

 

c

Type of address octet, which defines the used type of number (ton) and the numbering plan identification (npi).
Please consider that for types other than 129 or 145 dialing from phonebook with 

ATD><mem><n>

 is, depending 

on the network, not always possible (refer to 3GPP TS 24.008 

[32]

 subclause 10.5.4.7 for details).

If 

<type>

 is not specified the unknown 

<type>

=129 is used. If 

<number>

 contains a leading "+" 

<type>

=145 

(international) is used.
Supported values are: 

145

Dialing string 

<number>

 includes international access code character "+"

161

National number. The network support for this type is optional.

209

Dialing string 

<number>

 will be saved as ASCII string.

This is the default value, if 

<type>

 is not specified explicitly and characters 

other than "*", "#", "+" or "p" are included in 

<number>

.

Note that phonebook entries saved with this type cannot be dialed. 

255

Dialing string 

<number>

 is a command to control a Supplementary Service, 

i.e. "*", "#" codes are contained. Network support of this type is optional. 

129

Unknown number. If 

<type>

 is unknown and the 

<number>

 contains a lead-

ing "+", then this sign is removed. 

Text assigned to the phone number. The maximum length of this parameter is given in the test command 
response 

<tlength>

. When using an ASCII terminal, characters which are coded differently in ASCII and GSM 

have to be entered via escape sequences as described in Section 

1.6

, 

Supported character sets

. 

Maximum number of locations supported by the currently selected storage. For phonebooks located on SIM, 
this value varies depending on the SIM card. See 

AT+CPBS

 for typical values. 

Maximum length of phone number for "normal" locations. Depending on the storage, a limited number of loca-
tions with extended memory is available per phonebook. These locations allow storing numbers with twice the 
standard length, which is 2*

<nlength>

 digits for normal numbers, but only 

<nlength>

 digits for numbers 

saved with parameter 

<type>

= 209. If all extended locations of the selected phonebook are used up, then any 

attempt to write a number which requires extended memory will be denied with "+CME ERROR: invalid dial 
string". 

Maximum length of 

<text>

 assigned to the telephone number. The value indicated by the test command is 

given in octets. If the 

<text>

 string is given in GSM characters, each character corresponds to one octet. If the 

<text>

 string is given in UCS2, the maximum number of characters depends on the coding scheme used for 

the alpha field of the SIM. In the worst case the number of UCS2 characters is at least one less than half the 
number of GSM characters.
For a detailed description please refer to 3GPP TS 11.11 

[14]

, Annex B. 

Notes

•

Users should be aware that when using this AT command quickly after SIM PIN authentication the SIM data 
may not yet be accessible, resulting in a short delay before the requested AT command response is returned. 
See Section 

19.1

, 

Restricted access to SIM data after SIM PIN authentication

 for further detail. 

•

During 

AT+CPBW

 write command it is possible that in some cases returns "+CME ERROR: operation tempo-

rary not allowed". Use 

AT+CPBW

 write command again. 

•

DTMF transmission:
If a dial string contains the call modifier "p" the digits after this call modifier will be saved as DTMF tones. The 
DTMF tones 'A','B','C' and 'D' can not be saved due to BCD limitations. 

<type>

(num)

<text>

(str)(+CSCS)

<maxloc>

(num)

<nlength>

(num)

<tlength>

(num)

Confidential / Released

Summary of Contents for CINTERION BGS2T











































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CINTERION BGS2T

paystone Verifone Vx520 Quick Start Manual preview
Verifone Vx520
Brand: paystone Pages: 2
NEC P4WW-24TXH-A User Manual preview
P4WW-24TXH-A
Brand: NEC Pages: 28
Partner PT-6910 Series Unpacking And Setup Instructions preview
PT-6910 Series
Brand: Partner Pages: 2
Coinco Vantage Quick Start Manual preview
Vantage
Brand: Coinco Pages: 12
adyen Verifone VX675 User Manual preview
Verifone VX675
Brand: adyen Pages: 14
iMotion TC603 User Manual preview
TC603
Brand: iMotion Pages: 88
Glancetron MSR JC-1290 KB series Operation Manual preview
MSR JC-1290 KB series
Brand: Glancetron Pages: 30
E-Pos E-Touch Integrated User Manual preview
E-Touch Integrated
Brand: E-Pos Pages: 26
REINER SCT tanJack photo QR EN Operating Manual preview
tanJack photo QR EN
Brand: REINER SCT Pages: 24
Wasp WDT950 User Manual preview
WDT950
Brand: Wasp Pages: 81
CAN Albert Integration Manual preview
Albert
Brand: CAN Pages: 19
Colormetrics V1506 User Manual preview
V1506
Brand: Colormetrics Pages: 71
Barco DU5P Brochure preview
DU5P
Brand: Barco Pages: 6
Equinox Systems Apollo AiO Installation Manual preview
Apollo AiO
Brand: Equinox Systems Pages: 2
Equinox Systems APOLLO CFD Installation Manual preview
APOLLO CFD
Brand: Equinox Systems Pages: 2
Touch Dynamic Atlas All-in-one User Manual preview
Atlas All-in-one
Brand: Touch Dynamic Pages: 34
Tysso TP-9X16 User Manual preview
TP-9X16
Brand: Tysso Pages: 18
IVI CHECKMATE Elite 780 RF Installation Manual preview
Elite 780 RF
Brand: IVI CHECKMATE Pages: 2

Brands by name

Popular brands

Load more brands