manualshive.com logo in svg

Gema OptiSpray AP01.1, Operating Instructions Manual

Share
Download
Gema OptiSpray AP01.1 Operating Instructions Manual Download Page 37

 

Rev. 00  05/17 

 

OptiSpray AP01.1 

Decommissioning / Storage  

•

  37 

 

 

 

Decommissioning / Storage 

 

 

Decommissioning 

 

1. 

End the coating procedure 

2. 

Switch off the control unit 

 

 

The adjustments for high voltage, powder output volume and electrode 
rinsing air remain stored. 

If in disuse for several days 

 

1. 

Separate from power mains 

2. 

Clean guns, injectors and powder hoses (see therefore the 
corresponding user manuals) 

3. 

Turn off the compressed air main supply 

 

Storage conditions 

 

Hazard notes 

There is no danger to personnel or the environment if the unit is stored 
properly. 

Type of storage 

For safety reasons, the product should only be stored in a horizontal 
position 

Storage duration 

If the physical conditions are maintained, the unit can be stored 
indefinitely. 

Space requirements 

The space requirements correspond to the size of the product. 

There are no special requirements concerning distance to neighboring 
equipment. 

Summary of Contents for OptiSpray AP01.1

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands