![background image](http://html1.mh-extra.com/html/gehl/dynalift-663/dynalift-663_operators-manual_2205875036.webp)
907879/AP1198
34
PRINTED IN U.S.A.
Loading Machine Using Ramps
NOTE:
A matched pair of ramps is required.
1. See illustration above. The ramps MUST be of suf-
ficient strength to support the machine. Whenever pos-
sible, the use of strong steel ramps is recommended as
well as some type of center supporting block.
2. The ramps MUST be firmly attached to the truck
or trailer bed with NO step between the bed and the
ramps.
3. Incline of ramps MUST be less than 15 degrees;
ramp length MUST be at least 16 feet (4.8 m) long.
4. Ramp width MUST be at least 1-1/2 times the tire
width.
5. Slowly (at the lowest engine speed possible) and
carefully drive the machine up the ramps.
6. Remove the attachment tool from the boom.
Position the machine (with the boom facing toward the
front of the truck or trailer) so that it is straight in line
with the ramps. Tie down slots are provided on the
front and rear sides of the frame structure.
7. Block the front and rear of the tires on the truck or
trailer. Engage the parking brake.
In Transit
If in transit for a few days: (a) Disconnect the battery.
(b) Clean all bright surfaces and coat with heavy, very
high flash point grease to prevent rusting.
Unloading Machine Using Ramps
NOTE:
A matched pair of ramps is requIred.
Use ramps as described in Steps 1 thru 4 and proceed
as follows to unload the machine:
8. If necessary, adjust the machine so that the wheels
are in line and centered with the ramps.
9. Slowly (at the lowest engine speed possible) and
carefully drive the machine down the ramps
THEFT DETERRENTS
THE CERTAINTY OF APPREHENSION IS A
STRONG DETERRENT TO THEFT OF CON-
STRUCTION EQUIPMENT!
GEHL
has recorded all
part numbers and serial numbers. Users should take as
many of the following actions as possible to discour-
age theft, to aid in the recovery in the event that the
machine is stolen, or to reduce vandalism:
1. Remove keys from unattended machines.
2. Attach, secure, and lock all anti-vandalism and
anti-theft devices on the machine.
3. Lock doors of cabs when not in use.
4. Inspect the gates and fences of the vehicle storage
yard. If possible, keep machines in well lighted areas.
Ask the law enforcement agency having jurisdiction to
make frequent checks around the storage or work sites,
especially at night, during weekends, or on holidays.
5. Report the theft to the dealer and insurance com-
pany. Provide the model, and all serial numbers.
6. Request that your dealer forward this information
to
GEHL
Company.
Ramp Placement
WARNING
NEVER attempt to adjust travel direction (even
slightly) while traveling on the ramps. Instead,
back down off of the ramps and then realign
the machine with the ramps.
NEVER transport the machine with the boom
raised or extended. BE SURE to secure the
machine (including boom) to the truck or trail-
er bed using chain and binders of steel cables
to prevent any movement while transporting.
Summary of Contents for Dynalift 663
