Gefen HDSDI-2-DVIL User Manual Download Page 6

Supported Output Resolutions

The HD-SDI to DVI Loop supports all progressive scan resolutions up to 1920x1200; it 
does not support interlaced or 480p outputs.

Supported Input Resolutions

Input    

Resolution

HD-SDI  

All HD formats, NTSC, PAL, 2K-psf , 2K-p and 720p-50

SD-SDI  

NTSC, PAL

DVI-D  

All DVI-D interlaced and progressive scan formats up to 1920x1200

DVI-A  

All DVI-A RGB analog formats up to 1920x1200

OSD and INFRARED REMOTE FUNCTIONS

By default controls are unlocked. To lock press, “MUTING” for 4 seconds. The same 
process can be used to unlock the IR controls. The lock state of the HD-SDI to DVI 
Loop is saved even if the unit is turned off.

To access the OSD menu, press “RECALL”. The OSD will display six icons:

From left to right, these Icons represent:
Input Source Selection | Picture Settings | OSD Settings | Input Settings | Output 
Settings | Miscellaneous. 

To navigate through the menus, use the 2,8,4,6 button on your remote as Up, Down, 
Left, Right.  The table below explains all remote functions in both cases: On-screen 
display (OSD) ON or OFF.

OSD OFF
Type, Remote Control Key,  Function

•Input Select, CH +, Switch between HD-SDI, SDI, DVI-D, DVI-A
•Freeze picture, VOL -, Freeze/unfreeze the output displayRelock Input 1 Relock the 
output. Use in case the picture is not stable.
•Toggle IR lock, Press and hold MUTING for 4 seconds, Lock/unlock IR.
•Power, Press and hold POWER for 4 seconds, Restore HDSDI in settings (need to
reboot after.) and EDID detect mode.
*Force Flash Mode, Press and hold TV/VIDEO for 4 seconds, Displays a red screen to 
indicate that the unit is in fl ash mode and ready to be upgraded.
*Menu Access, RECALL, Access the menu system
*Force Output Mode, TV/Video + Number Key, Force the DVI-D to a specifi c resolution

OSD ON
Type, Remote Control Key,  Function

Up, 2, Navigate up
Down, 8, Navigate down
Left, 4, Navigate left
Right, 6, Navigate Right
Exit, 0, Exit submenu and menu
Select, ENTER or 5, Activate the selection

SUPPORTED INPUT/OUTPUT RESOLUTIONS

4

Summary of Contents for HDSDI-2-DVIL














Reviews: