background image

 

Using the Geemarc Professional Solar Watch Charger 

Plug the USB of the Geemarc solar watch charger into a USB port on your computer. 
Slide the On/Off Switch of the Geemarc solar watch charger to the On position. 
Place your watch face down on top of the charger. 
Use the appropriate rubber caps for the Cool LED Solar Charger 

 
When the Battery level is low

, the LCD shows a flashing empty battery and the second hand moves in 2 second jumps 

every 2 seconds. The buttons on the watch will not work. If you do not charge up the battery at this point the hands will 
eventually stop moving to save battery power. 

The hands will stop at 12 o’clock meanwhile the internal timekeeping is 

maintained. When the watch has been charged sufficiently, the watch will automatically match the internal timekeeping. 
Do not expect that your stopped solar watch will start to run once it is exposed to light! The watch will only start to run 
once light charges up the battery to a certain level. The charging time varies depending on the strength of the light and the 
level of charge found in the battery. If you do not recharge your watch for very long time, you will need to synchronize your 
watch  hands  with  the  LCD  time  (see  the  Synchronize  section)  and  then  set  the  time  and  calendar  according  to  the 
instructions below. 

Key Points about charging your watch:

 

1. 

Avoid  recharging at high temperature (over 60 oC)  e.g. placing it  on a dashboard  of a vehicle or too close to an 
electric lamp. This can damage your watch. 

2. 

Never allow the battery charge level to get close to empty. This can damage the battery and you will not be able to 
recharge and therefore will have to replace the damaged battery. 

Therefore, it is recommended that you charge your

 watch on a weekly basis with cool light. 

 
SETTINGS 

 

12/24 Hour Time Display on LCD 

1. Press and hold 

S2 

(the lower right button) for approximately 3 seconds. The display will show a flashing 12 H or 24 H 

2. Press 

S1

 to scroll through the two options (12H or 24H) and stop at the desired time format 

3. Press 

S2

 to Confirm and Exit 

Language Selection on LCD (English or German) 

1. Press and hold 

S2 

(the lower right button) for approximately 3 seconds. A flashing 12 H or 24 H will be displayed 

2. Press 

S2

 again. A flashing ENG or GER will be displayed 

3. Press 

S1

 to scroll through the options (ENG or GER). ENG= Weekday displayed in English GER= Weekday displayed in German 

4. Stop at the desired language 

5. Press 

S2

 to Confirm and Exit 

Time and Calender Setting on LCD   

The LCD time and Analogue time should be the same. 
If they do not match, synchronize them by following the  -

“Synchronize Watch Hands” instructions before proceeding with the following time 

setting instructions. 
 

1. Press and hold 

S2 

(the lower right button) for approximately 3 seconds. A flashing 12 H or 24 H will be displayed 

2. Press 

S2

 again. Flashing ENG or GER will be displayed 

3. Press 

S2

 again. A flashing hour digit will be displayed 

4. Press 

S1 

repeatedly to scroll to the correct hour 

5. Press 

S2

 to Confirm the selected hour. A flashing Minute digit will be displayed 

6. Press 

S1

 repeatedly to scroll to the correct minute 

 

Solar Watch 

Light 

    Lady size                    Man size 

Summary of Contents for Watch N Shake

Page 1: ...ch will not wake up and it will need charging first see Charging the Watch Enter Sleep Mode 1 Press S1 first and then S2 2 buttons are now being pressed simultaneously for around 5 seconds until QSM is displayed 2 Release both buttons 3 Press S1 SLP is displayed 4 The watch hands will spin and will stop at 12 00 am to sleep Charging the watch Solar Watch Charger not included but can be purchased s...

Page 2: ...is can damage your watch 2 Never allow the battery charge level to get close to empty This can damage the battery and you will not be able to recharge and therefore will have to replace the damaged battery Therefore it is recommended that you charge your watch on a weekly basis with cool light SETTINGS 12 24 Hour Time Display on LCD 1 Press and hold S2 the lower right button for approximately 3 se...

Page 3: ... this watch When an alarm is set off the watch will vibrate When the watch is vibrating the analogue hands pause and the LCD will switch off The vibrating alarm will stop after 15 seconds and then the LCD will be switched back on and the analogue hands will move rapidly to the correct time Alarm Time Check Press S3 once to show the first alarm time If you press S3 again the second alarm time will ...

Page 4: ...tep every 2 seconds and the Low Battery icon flashes telling you to recharge your watch When the Low Battery icon is flashing the vibration alarm and other button functions are disabled It is time to recharge your watch BATTERY CHANGE Battery Type This watch uses a ML2032 rechargeable battery Only trained jewelers or watch specialists should fit new batteries to avoid any damage to the watch Your ...

Reviews: