5 6 7 8
24. M icrophone
25. Charging pole
26. Speakerphone
27. Battery compartment cover
28. VOL+ (
)
- Increase the listening volume up to 30dB amplification, (Or
the ringer Volume when in quiescent mode).
- Switch On/Off the receiver Booster function (LED blue).
29. VOL- (
)
Decrease the listening volume. (Or the ringer volume when in
quiescent mode (until ringer turn OFF)).
MENU SETTING
The phone settings are always set in the same manner:
Base: Press
Menu/OK
button to open the main menu.
Then use the ▼▲buttons to select an entry and confirm it by
pressing the
Menu/OK
button.
The factory preset
PIN
code is
0000
Example:
Set the language on the base
Press
MENU / OK
,
then use
▼▲to select
LANGUAGE
,
press
MENU / OK
,
then use
▼▲ to select the desired
language and then press
MENU / OK
to confirm.
Base
PHONEBOOK
►VIEW►ADD►EDIT►DELETE►DELETE ALL►PB STATUS
CALL LOG:
►MISSED ►RECEIVED ►DIALLED
DATE & TIME
:
►TIME FORMAT ►SET CLOCK
LANGUAGE
►ENGLISH ►DEUTSCH ►FRANÇAIS ►ITALIANO
►NEDERLANDS…
SETTINGS
►RING SETUP ►DELETE HS ►DIAL MODE ►FLASH TIME
►KEY TONE ►CHANGE PIN ►BS DEFAULT
PAGE ALL HS
REGISTRATION
ANS. MACHINE
►MSG PLAYBACK ►DELETE ALL ►MEMO ►TAM ON/OFF
►TAM SETTINGS (ANSWER MODE, OGM SETTINGS,
ANSWER DELAY, RECORD TIME, TAM LANGUAGE, BS
SCREENING, REMOTE ACC, COMPRESSION, CHANGE PIN,
TAM DEFAULT)
USING THE HANDSET
Booster mode
During a call, when in boost mode, you can increase the
listening volume up to 30dB amplification.
- Press and Hold (2 seconds) the VOL+ button to activate
Boost mode (LED will be steady blue).
- Press and hold again the VOL+ button to cancel Boost
mode. (LED will go Off).
Storing a number to a picture memory button
On the base:
In predial mode
: Press and hold the picture memory button
to store the number entered from idle mode. You will hear a
beep of confirmation.
Using a picture memory
Press and hold the memory button, the handset dials the
memory number and the handset is in speakerphone mode.
REGISTRATION & DE-REGISTRATION
Note
: Handset and base station are pre-registered.
Up to five handsets can be registered to a single base station.
In the case of re-registration, the PIN code is
0000
.
Registration a photo handset
Base:
First place the base of the AMPLIDECT295 or AMPLIDECT
COMBI 295 in Registration mode.
Replace photo handset back on the charging pod, the red LED
flashes quickly to indicate registration in process.
You will hear a confirmation beep when the registration process
completes. It takes up to 60 seconds to complete the registration.
Note:
if the handset doesn’t arrive un registered, please
follow this procedure:
Handset:
Quickly press
[VOL+] [SP K] [VOL -] [SP K] [VOL+]
[VOL-] [SPK]
in idle mode, then HS will have a "Bi,Bi" tone
.
Registration a standard handset
On Handset:
Press
MENU/OK
select
▼▲ REGISTRATION,
Press
MENU/OK
select ▼▲BASE(1-4), Press
MENU/OK
enter PIN.
At the same time on
Base
: Press
MENU/OK
, select ▼▲
REGISTRATION, press
MENU/OK
to see PLEASE WAIT
(If the registration is successful, there will be a confirmation
beep).
De-Registration
On Base
: Press
MENU/OK
, use
▼▲to select
SETTINGS
,
press
MENU/OK
.
Use
▼▲to select
DELETE HS
, press
MENU/OK
enter
PIN, press
MENU/OK
Use
▼▲to select one of the handsets that you want to
de-register, press
MENU/ OK
to confirm.
INTERCOM
Internal Call
Base
: Press
INT/
/CLEAR (
)
, use
▼▲to select
HS 1 - 5
, press
MENU /OK
to connect.
Handset
: Function not available.
Call All Handsets
Base
: Press
INT/
/CLEAR (
)
, use
▼▲to select
ALL HANDSETS
, press
MENU /OK
to connect.
Transfer an External Call
Base
: Press
MENU /OK
, select ▼▲handset number,
press
or
on hands et. After connection quit the call
on base.
Conference Call
Base
: Press
MENU / OK
,
Enter the desired handset number on keypad.
After connection press and hold
until CONFE RENCE is
shown.
ANSWERING MACHINE
Your telephone base includes a telephone answering machine
that
records unanswered calls when it is on. The answering
machine can store up to 59 messages within the maximum
recording time of approximately 15 minutes. As well as
recording incoming messages, you can record memos for other
users of your phone.
Press
ANS ON/OFF
to switch the answering machine
ON or OFF
Remote operations
If you are away from your home, you can call your answering
machine to switch on or off the answering machine and listen
to your messages remotely using another tone-dialing phone.
1. Place a call from a tone-dialing phone.
2. When the answering machine answers the call and starts
playing OGM, press
.
3. Enter the 4-digit Remote Access PIN (default PIN is
0000
).
4. Press the following keys to carry out your desired function.
A
Functions
While message is not
playing
While message is playing
2
Delete the current message
playback
4
Repeat playing the current
message from the beginning.
Press twice to skip backward to
the previous message.
5
Play the message
6
Skip forward to play the next
message
7
Turn on the answering
machine
8
Stop the current message
playback
9
Turn off the answering
machine
*
Enter the 4-digit remote
access PIN
NOTE:
When your answering machine memory is full and the answer
mode is in ANS & RECORD, the answer mode will change to
ANSWER ONLY automatically.
It will change to ANS & RE CORD mode automatically after
some messages have been deleted.
You cannot delete new messages before they are listened.
MAINTENANCE
Clean the surface of the housing with a soft, fluff-free cloth.
Do not use any cleaning agents or solvents.
GUARANTEE
From the moment your Geemarc product is purchased,
Geemarc guarantee it for the period of two years. During this
time, all repairs or replacements (at our discretion) are free of
charge. Should you experience a problem then contact our
help line or visit our website at
www.geemarc.com
.
The guarantee does not cover accidents, negligence or
breakages to any parts. The product must not be tampered
with or taken apart by anyone who is not an authorized
Geemarc representative.
The Geemarc guarantee in no way limits your legal rights.
IMPORTANT :
YOUR RE CEIP T IS PART OF Y OUR
GUA RANTEE AND MUS T BE RE TA INE D AND PRODUCE D
IN THE EVENT OF A WARRANTY CLAIM.
Please note: The guarantee applies to the United
Kingdom only.
DECLARATIONS:
CE Directives
Geemarc Telecom SA hereby declares that this product is in
compliance with the essential requirements and other relevant
provisions of the Radio and Telecommunications Terminal
Equipment Directive 2014/53/UE.
The CE declaration of conformity may be consulted at
www.geemarc.com
Electrical connection:
The apparatus is designed to operate from a 230V 50Hz
supply only. (Classified as hazardous voltage according to
EN60950 standard). The apparatus does not incorporate an
integral power on/off switch. To switch off the apparatus,
disconnect the power adaptor.
When installing the apparatus, ensure that the mains power
socket is readily accessible.
Telephone connection:
Voltages present on the t elecommunic ation network are
classified TNV-3 (Telec ommunication Net work Voltage)
according to the EN60950 standard.
Recycling Directives
The WEEE (Waste Electrical and Electronic Equipment) has
been put in place for the products at the end of their useful
life are recycled in the best way.
When this product is finished with, please do not put it in your
domestic waste bin. Please use one of the following disposal
options:
- Remove the batteries and deposit them in an appropriate
WEEE skip.
Deposit the product in an appropriate WEEE skip.
- Or, hand the old product to the retailer. If you purchase a
new one, they should accept it.
Thus if you respect these instructions you ensure human
health and environmental protection.
For product support and help visit our website at
www.geemarc.com
United Kingdom: 5B Swallow Court, Swallowfields, Welwyn
Garden City, Hertfordshire, AL7 1SB,UK
telephone
01707 387602
fax
01707 832529
UGAMPLIDECT.COMBI-PHOTO.295_En_A3_V1.1
