manualshive.com logo in svg

Geeetech A20T, User Manual, Page: 50 / 54

Share
Download
Geeetech A20T User Manual Download Page 50

 

50 

 

SHENZHEN GETECH TECHNOLOGY CO., LTD 

10.3 Filament run-out sensor (Optional) 

Before  using  this  function,  please  check  whether  it  is  turned  on  or  not.  Choose 

“Control”>”Filament”>“Runout  sensors” 

and  make  sure  it  shows 

“ON”

.  See  pictures  (10-3, 

10-4). 

 

(Picture 10-3)                            (Picture 10-4) 

 

It  will  pop  up  the  notification

  “Err:  No  Filament”

  when  the  filament  is  run  out  during 

printing and the printer will stop. See picture (10-5). 

 

Press the extruder handle, remove the remaining filament before loading the new filament. 

 

When the filament is loaded, use a tweezers to clean the nozzle. Press the knob to enter the 
main menu, and choose “Resume print” to re-start the printing. See picture (10-6). 

 

 

(Picture 10-5)                                                      (Picture 10-6) 

10.4 3D touch for auto bed leveling (Optional) 

This  printer  supports  auto  bed  leveling.  Refer  to  the  link  below  to  know  how  to  install  the  3d 
touch sensor. 

https://www.youtube.com/watch?v=_RtsZDbR2po&t=66s

 

Visit our official forum 

http://www.geeetech.com/forum/

 

 

 

Summary of Contents for A20T























































Reviews:

No comments