manualshive.com logo in svg

GEA Omni, Instruction Manual

Introducing the Instant Omni - your ultimate kitchen companion! Achieve culinary excellence effortlessly with its innovative features and user-friendly interface. Unlock the full potential of your Instant Omni by accessing the comprehensive User Manual for free. Download it now from manualshive.com, and master your culinary skills with ease.

Share
Download
background image

4.2.1

List and Description of Compressor Warnings

Warning

Explanation

High Motor Current Warning

This annunciation will be triggered if the motor current reading exceeds the
value obtained by subtracting the 

High Motor Current Warning Offset

 param-

eter from the 

High Motor Current Shutdown

 parameter.

High Suction Pressure Warning This annunciation will be triggered if the suction pressure reading exceeds

the value obtained by subtracting the 

High Suction Pressure Warning Offset

parameter from the 

High Suction Pressure Warning

 parameter.

High Discharge Temperature
Warning

This annunciation will be triggered if the discharge temperature reading
exceeds the value obtained by subtracting the 

High Discharge Temperature

Warning Offset

 parameter from the 

High Discharge Temperature Shutdown

parameter.

High Discharge Pressure Warn-
ing

This annunciation will be triggered if the discharge pressure reading exceeds
the value obtained by subtracting the 

High Discharge Pressure Warning Off-

set

 parameter from the 

High Discharge Pressure Shutdown

 parameter.

High Oil Separator Tempera-
ture Warning

This annunciation will be triggered if the oil separator temperature reading
exceeds the value obtained by subtracting the 

High Oil Separator Tempera-

ture Warning Offset

 parameter from the 

High Oil Separator Temperature

Shutdown

 parameter.

Low Oil Separator Temperature
Warning

This annunciation will be triggered if the oil separator temperature reading
falls below the value obtained by adding the 

Low Oil Separator Temperature

Warning Offset

 parameter to the 

Low Oil Separator Temperature Shutdown

parameter.

High Oil Separator Level Warn-
ing

This annunciation will be triggered if the oil separator high level input
becomes de-energized for a period of time that exceeds the value of the

High Oil Separator Level Warning Timer

.

High Oil Temperature Warning

This annunciation will be triggered if the oil separator temperature reading
exceeds the value obtained by subtracting the 

High Oil Separator Tempera-

ture Warning Offset

 parameter from the 

High Oil Separator Temperature

Shutdown

 parameter.

Low Oil Temperature Warning

This annunciation will be triggered if the oil temperature reading falls below
the value obtained by adding the 

Low Oil Temperature Warning Offset

parameter to the 

Low Oil Temperature Shutdown

 parameter.

High Oil Filter Differential Warn-
ing

This annunciation will be triggered if the calculated oil filter differential
exceeds the value obtained by subtracting the 

High Oil Filter Differential

Warning Offset

 parameter from the 

High Oil Filter Differential Shutdown

parameter.

Instruction Manual | GEA Omni™
Control panel

Annunciations

Warnings

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

215

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

D+H RZN 4503-T Original Instructions Manual preview
RZN 4503-T
Brand: D+H Pages: 36
D-Box HEMC Getting Started preview
HEMC
Brand: D-Box Pages: 4
D+H RZN 4416-M Manual preview
RZN 4416-M
Brand: D+H Pages: 36
FAAC XT4 433 RC User Manual preview
XT4 433 RC
Brand: FAAC Pages: 4
FAAC E391 Manual preview
E391
Brand: FAAC Pages: 52
Lawler 804 Installation & Maintenance Manual preview
804
Brand: Lawler Pages: 5
Velleman VM130V2SET Quick Start Manual preview
VM130V2SET
Brand: Velleman Pages: 26
Velleman VM151 Manual preview
VM151
Brand: Velleman Pages: 32
Velocity MMP Operation And Maintenance Manual preview
MMP
Brand: Velocity Pages: 84
Panasonic KX-A16B Quick Start Manual preview
KX-A16B
Brand: Panasonic Pages: 8
Absima CR9T Quick Start preview
CR9T
Brand: Absima Pages: 5
Harman FG2106-04 Quick Start Manual preview
FG2106-04
Brand: Harman Pages: 2
Linear Technology LT3507 Demo Manual preview
LT3507
Brand: Linear Technology Pages: 6
Nortek WRC4 Owner'S Manual preview
WRC4
Brand: Nortek Pages: 24
WANDERS EcoWave Symax User Instructions preview
EcoWave Symax
Brand: WANDERS Pages: 16
FUHR SmartTouch 2.0 Installation, Operating And Maintenance Manual preview
SmartTouch 2.0
Brand: FUHR Pages: 20
Powtran PR5200 Series Manual preview
PR5200 Series
Brand: Powtran Pages: 36
Quick THRUSTER COMMAND TCD 1022 E Manual For Use And Installation preview
THRUSTER COMMAND TCD 1022 E
Brand: Quick Pages: 56

Brands by name

Popular brands

Load more brands