GEA Omni Page 195 Instruction Manual Download

Page: 195 / 238

Remote Set Point

fig.109:

Remote Set Point Options

Remote Set Point

This drop down list is used to select which function, if any, is to be controlled through the use of a remote
device such as a PLC.

Remote Pressure Scaling

This drop down list is only used if the pressure control for the package is being handled remotely. It is
used to select the range for the pressure.

Suction

fig.110:

Suction options

Suction Pressure Scaling

This is used to select the range of the suction pressure transducer.

Suction Pressure Max

This is used to select the maximum value that may be assigned to the suction pressure parameters of
the compressor. The value is measured in PSIG.

Suction Temperature Max

This is used to select the maximum value that may be assigned to the suction temperature parameters
of the compressor. The value is measured in degrees Fahrenheit.

Discharge

Instruction Manual | GEA Omni™
Control panel

Control

Configuration

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

195

Summary of Contents for Omni















































































































































































































































Search results

Summary of Contents for Omni

Reviews:

Related manuals for Omni

Brands by name

Popular brands

GEA Omni, Instruction Manual

Search results

Summary of Contents for Omni

Reviews:

Related manuals for Omni

Brands by name

Popular brands