GE ZICS360 LH Installation Instructions Manual Download Page 12

12

STEP 5  LEVEL REFRIGERATOR

All models have 4-point leveling. The front is 
supported by leveling legs, the rear is supported by
adjustable wheels. Both are accessible from the front
of the refrigerator.
• To level the back of the refrigerator, turn the 

7/16" hex nut located above the front wheels. Turn
clockwise to raise or counterclockwise to lower the 
refrigerator.

• For front leveling, use a 1-1/4" open-end wrench.
• Adjust height of refrigerator to match installation

cutout opening 83-1/2 to 84-1/2". The refrigerator
should be level and plumb with cabinetry.

STEP 6  SECURE REFRIGERATOR 

TO CABINETRY

Whenever possible, perform this step for anti-tip 
security, or when anti-tip brackets cannot be used. 

The refrigerator must be secured to prevent tipping

.

• Raise the grille panel to access case trim. 
• Drill hole in trim and drive screw through the trim

into adjacent cabinet.

• Follow the same procedure on the opposite side.

Leveling Leg

Hex Nut Adjusts

Rear Wheels

Drive Screws

Through Case Trim and Into

Adjacent Cabinets

CAUTION: 

The rear leveling wheels and front leveling legs are
limited to a maximum height adjustment of 1". If the
installation requires more than 84-1/2" height, the
installer should elevate the refrigerator on a sheet of
plywood or runners. Cabinetry trim could also be
added across the top of the opening to shorten the
opening. 

If you attempt to raise the refrigerator

more than 1", you will damage the front leveling legs
and the rear leveling wheels.

PRUDENCE

Les roues de nivellement arrière et les pattes de 
nivellement avant permettent un réglage maximal 
de 25 mm (1 po). Si l’ouverture pour le réfrigérateur
a une hauteur supérieure à 2,15 m (84-1/2 po), 
l’installateur doit élever le réfrigérateur sur une
feuille de contre-plaqué ou des glissières. Il est 
également possible d’ajouter des baguettes de 
finition des placards sur le haut de l’ouverture afin
de la réduire. Lever le réfrigérateur de plus de 
25 mm (1 po) endommage les pattes de nivellement
avant et les roues de nivellement arrière.

Installation Instructions

Summary of Contents for ZICS360 LH





















Reviews: