background image

Installation Instructions

4

TOOLS REQUIRED

• #2 Phillips screwdriver
• Adjustable wrench

PARTS SUPPLIED

• Monogram nameplate
• Hardware for changing door swing
• Optional stainless steel toekick with screws

and spacers

• Left and right side hinge covers
• Top screw hole cover

GROUNDING THE WINE CHILLER,
WINE RESERVE AND BEVERAGE
CENTER

IMPORTANT –

 

Please read carefully.

FOR PERSONAL SAFETY, THIS APPLIANCE MUST
BE PROPERLY GROUNDED.

The power cord of this appliance is equipped with a
three-prong (grounding) plug which mates with a
standard three-prong (grounding) wall receptacle to
minimize the possibility of electric shock hazard from
this appliance.

Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered,
it is your personal responsibility and obligation to
have it replaced with a properly grounded 3-prong
wall outlet.

DO NOT, UNDER ANY
CIRCUMSTANCES, CUT
OR REMOVE THE THIRD
(GROUND) PRONG
FROM THE POWER CORD.

DO NOT USE AN ADAPTER PLUG TO CONNECT
THE REFRIGERATOR TO A 2-PRONG OUTLET.

DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE.

STEP 1   REMOVE PACKAGING

• Remove corner blocks and foam drawer stops.
• Remove all packing material, tape and protective

plastic coverings.

• Remove stainless steel toekick taped to the back

of the unit.

CAUTION:

 Small objects are a choke

hazard for children. Remove and discard any parts
not used.

MISE EN GARDE :

 

Les petits

objets peuvent étrangler les enfants. Il faut jeter
toutes les piéces qui ne sont pas utilisées.

STAINING WOOD DRAWER FRONTS

The drawer fronts are unfinished cherry wood.
During use, oil from hands may accumulate and stain
the wood.
• The drawer fronts may be stained and sealed to

match adjacent cabinetry. The tinted glass will
make the stained wood appear darker. A true color
match can be seen only when the door is opened.

• Apply the stain and sealer according to the

manufacturer’s instructions. To avoid unpleasant
odor, keep the door open to ventilate and allow
the stain/sealer to dry completely before using
the product.

Summary of Contents for Wine Chiller Wine Reserve and Beverage Center









Reviews: