manualshive.com logo in svg

GE WDSS4120, Technical Service Manual, Page: 26 / 46

Share
Download
GE WDSS4120 Technical Service Manual Download Page 26

To avoid risk of electrical shock, personal injury, or
death, disconnect power to unit before servicing.

Disassembly Procedures

23

WARNING

!

Loading
  door

5. Maneuver loading door from washer cabinet top.

Loading
  door

6. Remove screws securing right hinge and remove

loading door.

7. Reverse procedure to reassemble.

Agitator

1. Open loading door.
2. Remove agitator by placing hands under agitator

lip and pull upward, if agitator is stuck or
stubborn use agitator belt WX5X1326 under bottom
edge of agitator.

3. Using a rocking motion (side-to-side) carefully lift

agitator up off drive bell.

4. To reassemble place agitator on top of drive bell.

Slowly rotate agitator until fingers on underside of
agitator line up with large slots on drive bell.

5. A sharp blow on top of agitator, with the palm of

your hand, will force agitator down onto drive
bell, allowing fingers on underside of agitator to
lock under bottom edge of drive bell.

NOTE: Do not push agitator onto drive bell any

further than necessary.

Agitator, Drive Bell and Seal Assembly

NOTE: If water is present in washtub, remove water

before attempting to remove drive bell.

1. Remove agitator, see “Agitator” procedure.
2. Remove plug and 

7

/

16

" bolt from top of drive bell.

3. Using care pry drive bell upward off transmission

shaft.

4. Remove old seal from hub assembly by:

a. Placing a flat bladed screwdriver between

bottom edge of seal and hub.

b. Using washtub bolts as a pry area, pop off

lower seal bead.

c. Grasping bottom of seal and pulling straight up

freeing upper seal bead.

Hex
nut

    Hub
assembly

    Hub
shoulder

Bronze
bearing

Washer

Transmission
output shaft

5. Clean all foreign material from seal mounting

area of hub assembly, bronze bearing and
washer.

6. Lubricate new seal with liquid soap or soapy

water to aid in assembly of seal onto hub.

Summary of Contents for WDSS4120















































Reviews:

No comments