GE Vivid S70 User Manual Download Page 684

Page: 684 / 709

Peripherals

14-14

Vivid S70 / S60

–

User Manual

BC092760-1EN

The size and position of the window can be adjusted by using
the rotary control below the View-X button (Figure 14-7).

Figure 14-7. Rotary control for View-X size and position

TCP/IP Configuration for View-X

Streaming source and client configuration is set through the

Video Streaming

settings:

1. Press

Utility/Config

on the Touch panel and log on as

administrator if required.

2. Select the

Connectivity

category and the

Tcpip

subgroup.

3. Select

Video Streaming

(Figure 14-8).

Summary of Contents for Vivid S70





































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Vivid S70

Reviews:

Related manuals for Vivid S70

Brands by name

Popular brands

GE Vivid S70, User Manual

Search results

Summary of Contents for Vivid S70

Reviews:

Related manuals for Vivid S70

Brands by name

Popular brands