background image

GE
P

ART

 N

UMBER

 FN091065, R

EVISION

 2

VS5 N 

AND

 VS6 N 

S

ERVICE

 M

ANUAL

3-2

 - 

P R E L I M I N A R Y

Section 3-2
Installation Reminders

3-2-1

Average Installation Time

The Vivid S5 N or Vivid S6 N installation and functional checkout will take approximately one hour; Vivid 
S5 N or Vivid S6 N consoles with optional equipment may take slightly longer.

Once the site has been prepared, the average installation time required is shown in 

Table 3-2

 below.

3-2-2

Installation Warnings

1.) The Vivid S5 N or Vivid S6 N ultrasound scanner weighs 65 Kgs (143 lbs), without 

add-ons/peripherals. 
Two people are always required to unpack the system.

2.) There are no operator-serviceable components. To prevent shock, do not remove any covers or 

panels. If problems or malfunctions occur, unplug the power cord. Only qualified service personnel 
should carry out servicing and troubleshooting.

NOTE:

For information on shipping carton labels, refer to 

Figure 3-1 on page 3-5

 and 

Figure 3-4 on 

page 3-7

.

3-2-2-1

System Acclimation Time

Following transport, the Vivid S5 N or Vivid S6 N system may be very cold, or hot. Allow time for the 

system to acclimate before being switched ON. Acclimation requires 1 hour for each 2.5

o

C increment, 

when the temperature of the system is below 10

o

C or above 35

o

C. 

NOTE:

After a long period of storage, or after transportation of the system with the monitor in the folded-down 
position, it is highly recommended to place the monitor in the upright position - and to leave it in this 
position for a period of longer than 1 hour before use. This will enable it to properly adjust to the 
environmental conditions.

Table 3-2

   Average Installation Time

Description

Average 

Installation Time

Comments

Unpacking the scanner

30 minutes

Installing the scanner

30 minutes

Time may vary, according to the required configuration

DICOM Option

(connectivity)

30 minutes

Time may vary, according to the required configuration

CAUTION

Turning the system ON after arrival at the site - without allowing time for acclimation - may 
cause system damage!

Table 3-3

   Vivid™ S5 N and Vivid™ S6 N System Acclimation Time

°

C

60

55

50

45

40

35

30

25

20

15

10

5

0

-5

-10

-15

-20

-25

-30

-35

-40

°

F

140

131

122

113

104

96

86

77

68

59

50

41

32

23

14

5

-4

-13

-22

-31

-40

Hrs

8

6

4

2

0

0

0

0

0

0

0

2

4

6

8

10

12

14

16

18

20

Summary of Contents for Vivid S5 N



































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews: