GE Spacemaker GSM1860NSS Installation Instructions Manual Download Page 9

STEP 9  POSITION DISHWASHER UNDER COUNTERTOP

• Check to be sure that wires are secure under the

dishwasher and not pinched or in contact with door
springs or other dishwasher components.

TIP: 

Check tub insulation blanket, if equipped. It should

be positioned so it is not bunched up or interfering with
door springs. Check by opening and closing the door.

• Push dishwasher into cabinet. The front corners of the

dishwasher door should be flush with cabinet doors.
Be careful not to dent font panel with knees or damage
countertop or cabinets with dishwasher parts.

Figure P

Installation Instructions

8

Figure Q

 

STEP 10  LEVEL DISHWASHER

IMPORTANT

 –

  

Dishwasher must

be level for proper dish rack operation and wash
performance.

TIP: 

Pull lower rack out, about halfway. Check to

be sure the rack does not roll forward or back into
dishwasher. If the rack rolls in either direction, the
dishwasher must be leveled again.
• If door hits the tub, the dishwasher is not installed

correctly. Adjust leveling legs to align door to tub.

• Level the dishwasher

by adjusting the
four leveling legs
individually.

Figure R

• Place level on

door and rack
track inside the
tub as shown to
check that the
dishwasher is
level.

Turn Legs

to Adjust

Do Not Push Against
Front Door Panel With 
Knee. Damage to The 
Door Panel Will Occur.

Reposition Dishwasher
by Grasping Both
Sides With Hands

Check

Level

Side

To Side

Check

Level

Front

to Back

Summary of Contents for Spacemaker GSM1860NSS














Reviews: