background image

Parts Included

Installation Instructions

for your new

Before you begin - Read these instructions completely and carefully.

IMPORTANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES. 

Note to Installer – Be sure to leave these instructions with the Consumer. 

Note to Consumer – Keep these instructions with your Owner’s Manual for future reference

.

RAVTRANS

Transition Plenum

   31-30824-2      06-17 GEA

GE is a trademark of the General Electric Company. Manufactured under trademark license.

 

Installation  

Overview 

(Small Chassis Shown)

Existing

Architectural 

Louver

Exterior/ 

Outside Wall

Existing

Wall Plenum

Unit

RAVWP6 

– 6” D x 19-3/4” W x 32” H

RAVWP8 

– 8” D x 19-3/4” W x 32” H

RAVWP12 

– 12” D x 19-3/4” W x 32” H

RAVWP15 

– 15” D x 19-3/4” W x 32” H

RAVTRANS Kit will fit the following GE Appliances plenum kits:  RAVWP6, RAVWP8, RAVWP12 and RAVWP15. 

RAVTRANS kit is required when replacing an AZ75/AZ85 series vertical air conditioner with a new AZ90/91 

series vertical air conditioner.  Differences in chassis designs between the AZ75/AZ85 series and AZ90/91 

series require careful installation planning.  Changes in drain exit locations and drain routing, electrical 

connections, platform height, conditioned air duct location and additional space requirements for installation of 

RAVTRANS kit are all items that need to be considered when replacing a AZ75/AZ85 series unit with an AZ90/91 

series unit.

Installation of a new AZ90/91 series unit with a transition plenum will take up approximately 2-1/2” of additional 

closet space once the unit is fully installed. Before starting the conversion be sure there is adequate closet 

space to meet the manufacture’s recommend minimum clearance requirements.

Transitional 

Wall Plenum

Insulation

Drain Pan

Flange

Mounting 

screw 

locations

Unit Side

Transition Plenum

6 - #8 3/4” hex head sheet metal screws

4 - Pieces of Insulation 

1 - Drain Pan

Transition

Wall Plenum

Existing Wall 

Plenum Side

(2) Top and Bottom 

Pieces of Insulation

(2) Side Pieces 

of Insulation

Drain Pan

Summary of Contents for RAVWP12







Reviews: