GE PT7800DHWW Installation Instructions Manual Download Page 3

2 C

  CUTOUT FOR DOUBLE OVENS (2 THERMAL OVENS)

NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim 

both sides equally to establish the cutout width.

Dim.

Description

27” Double Oven

30” Double Oven with 

Pedestal

30” Double Oven 

without Pedestal

A

Cabinet Width

27” (68.6 cm)

30” (76.2 cm)

30” (76.2 cm)

B

Cutout Width

25” (63.5 cm) min.  

25

1

ø

4

” (64.1 cm) max.

28

1

ø

2

” (72.4 cm) min.  

28

5

ø

8

” (72.7 cm) max.

28

1

ø

2

” (72.4 cm) min.  

28

5

ø

8

” (72.7 cm) max.

C

Cutout Height

49

11

ø

16

” (126.2 cm) min.  

50

1

ø

8

” (127.3 cm) max.

51

13

ø

16

” (131.6 cm) min.  

51

15

ø

16

” (131.9 cm) max.

50 ¼” (127.64cm) 

D

Overlap of Oven 

Over Side Edges 

of Cutout

1” (2.5 cm)

11

ø

16

” (1.75 cm)

11

ø

16

” (1.75 cm)

E

Clearance to 

Adjacent Corners, 

Drawers, Walls, etc., 

When Door Is Open

23” (58.4 cm) min.

23” (58.4 cm) min.

23” (58.4 cm) min.

F

Overlap of Oven 

Top of Cutout

1” (2.5 cm) min.

1” (2.5 cm) min. 

(1

1

ø

4

” (3.2 cm) for PT9550)

1” (2.5 cm) min. 

(1

1

ø

4

” (3.2 cm) for PT9550)

G

Overlap of Oven 

Bottom of Cutout

1” (2.5 cm) min.

1

1

ø

4

” (3.2 cm)

1

1

ø

4

” (3.2 cm)

H

Junction Box 

Location 

8

3

ø

4

” (22.2 cm) max. 

right side only

9

1

ø

2

” (24.1 cm) max. 

right side only

9

1

ø

2

” (24.1 cm) max. 

right side only

J

Height to Bottom 

of Junction Box

44” (111.8 cm)

47” (119.4 cm)

47” (119.4 cm)

K

Recommended 

Cutout Location 

from Floor

13

1

ø

4

” (33.7 cm)

12” (30.5 cm)

12” (30.5 cm)

2 D

  CUTOUT FOR DOUBLE OVENS (with Upper Microwave Oven)

NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim 

both sides equally to establish the cutout width.

Continue to Section 3 for DWO with Pedestal. Otherwise, continue to Section 4.

Continue to Section 4.

H

B

C

K

F

G

D

A

J

E

Junction 

Box 

Location 

(junction 

box may 

be located 

in adjacent 

cabinet)

Cutout Depth  

23-1/2”  

(59.7 cm) Min.

Dim.

Description

27” Oven 

with Microwave

30” Oven 

with Microwave

A

Cabinet Width

27” (68.6 cm)

30” (76.2 cm)

B

Cutout Width

25” (63.5 cm) min.  

25

1

ø

4

” (64.1 cm) max.

28

1

ø

2

” (72.4 cm) min.  

28

5

ø

8

” (72.7 cm) max.

C

Cutout Height

41

1

ø

8

” (104.5 cm) min.  

41

1

ø

4

” (104.8 cm) max.

42

3

ø

16

” (107.2 cm) min.  

42

1

ø

4

” (107.3 cm) max.

D

Overlap of Oven Over Side Edges 

of Cutout

1” (2.5 cm)

11

ø

16

” (1.75 cm)

E

Clearance to Adjacent Corners, 

Drawers, Walls, etc., When Door 

Is Open

23” (58.4 cm) min.

23” (58.4 cm)

F

Overlap of Oven Top of Cutout

1” (2.5 cm) min.

1” (2.5 cm) min.

G

Overlap of Oven Bottom of Cutout

1” (2.5 cm) min.

1

1

ø

4

” (3.2 cm)

H

Junction Box Location 

8

3

ø

4

” (22.2 cm) max. 

right side only

9

1

ø

2

” (24.1 cm) max. 

right side only

31-11044   08-16   GEA

Summary of Contents for PT7800DHWW

















Reviews: