GE Profile PDWF400P Installation Instructions Manual Download Page 9 | Manualshive

Page: 9 / 16

Dishwasher Installation

STEP 9 – POSITION WATER LINE AND

HOUSE WIRING

• Position water supply

line and house wiring
on the ﬂ oor of the
enclosure to avoid
interference with
base of dishwasher
and components
under dishwasher.

Figure P

Figure Q

��

��

��

��

��

��

��

��

��

• Do not over tighten the 90° elbow, water valve bracket could

bend or water valve ﬁ tting could break.

• Position the end of the elbow to face the rear of the

dishwasher.

STEP 8 – INSTALL 90° ELBOW

• Wrap 90° elbow with thread seal tape.
• Install a 90° elbow onto the water valve.

Front of Dishwasher

90°

Elbow

Thread

Seal Tape

Fill

Hose

Water Valve

Bracket

05A-1183AA

STEP 10 – INSTALL DRAIN HOSE TO

DISHWASHER DRAIN PORT

In this step you will need the drain hose and clamp set aside in
Step 1.
• Stand dishwasher upright.
• Place drain hose clamp over 1-3/16" inside diameter end of

drain hose with the clamp screw positioned on the bottom of
the hose.

IMPORTANT

– Prevent drain hose damage and

possible leaks. Be careful not to nick or cut the drain hose.

• Push the end of the drain hose over the drain pump outlet

being careful not to disturb the check valve. Refer to Figure Q.

• Seat the drain hose end against the hose stops on the pump

outlet.

• Position hose clamp against the front lip of the drain hose

and tighten clamp.

06E-1774C

Hose Clamp

Hose Stops

Pump Outlet

Check

Clamp screw on

bottom of hose

Valve

Do Not Remove

Note:

Drain hose

supplied with dish -
washer is approxi-
mately 78" long. If a
longer hose is
needed, a 120" long
hose (10 feet) may
be purchased from
an authorized
GE appliance
dealer. The
10' long
hose is
part
number

GPF10L

.

Tip for leak free connections:

• Insert hose against stop on pump.
• Position clamp against front lip of drain hose.
• Tighten clamp to at least 15 inch-pounds of torque.

Tip for quiet drain pump operation:

Position hose clamp with clamp screw on the bottom side of
the hose. This will prevent the clamp from coming in contact
with the rear brace. Clamp contact with the rear brace could
create noise when the drain pump is running.

Figure O

9

«
...
7
8
9
10
11
...
»

Summary of Contents for Profile PDWF400P

















Reviews:

No comments