7
C
o
n
su
m
er
S
u
p
p
o
rt
Tr
o
u
b
le
sh
o
o
tin
g
T
ip
s
O
p
er
a
tin
g
In
st
ru
ct
io
n
s
Sa
fe
ty
In
st
ru
ct
io
n
s
GEAppliances.com
Options
The light above the selected pad will be
On
to indicate which option has been selected.
STEAM
For use with heavily soiled and/or dried-on, baked-on soils. This option
MuST
be selected
prIOr
to starting the cycle.
The
STEAM
option adds 24 minutes to the cycle time.
HEATED DRY
Shuts off the drying heat option. Dishes air dry naturally and energy is saved. For faster air dry,
light oFF
you can prop the door open after the
ClEAn
light illuminates.
HEATED DRY
Turns the heater on for faster drying. This will extend the total cycle time between
light on
8 and 38 minutes depending on the cycle selected.
nOTE: HEATEd dry
cannot be
selected with
rInSE Only
cycle.
LOCK
You can lock the controls to prevent any selections from being made. or you can lock the controls
after you have started a cycle.
children cannot accidentally start dishwasher by touching pads with this option selected.
To LOCK the dishwasher control,
touch and hold the
HEATEd dry
pad for 3 seconds. The light
below the
HEATEd dry
pad will turn on.
To UNLOCK the dishwasher control,
touch and hold the
HEATEd dry
pad for 3 seconds. The
lOCK
light will turn off.
ADDED
When selected, the cycle will run longer with the heating element on to improve both wash and
HEAT
dry performance.
nOTE:
Cannot be selected with
rInSE Only
cycle.
DELAY HOURS
You can delay the start of a wash cycle for up to 9 hours. Touch the
dElAy HOurS
pad to choose
the number of hours you want to delay the start of the cycle; then touch
STArT/rESET
one time.
The dishwasher will count down and start automatically at the correct time.
Touching
STArT/rESET
a second time will cancel the
dElAy STArT
selection
.
RESET
To change a cycle after washing starts, touch the
STArT/rESET
pad to cancel the cycle. For some
models, the
STArT/rESET
light will flash while the water is pumped out. This takes approximately
90 seconds. The door must be closed to complete pump out. When the light stops flashing, the
dishwasher can be reprogrammed and restarted. Buttons will not respond during pump out.
For other models, the
STArT/rESET lEd
will turn off and the drain pump will pump water out of
the dishwasher for 90 seconds and then turn off. Cycle selection and option
lEd
’s will remain on,
and buttons will respond during pump out. If the
STArT/rESET
is pressed while the dishwasher is
in pump out, the
STArT/rESET lEd
will turn on and the dishwasher will start a new wash cycle
Start
Close and latch the dishwasher door and select the cycle and desired enhancements. Touch the
STArT/rESET
pad once to begin the cycle. Water begins to fill the dishwasher, and approximately
60 seconds later the wash action begins.
nOTE:
The dishwasher remembers your last cycle so you don’t have to reprogram each time.
When the dishwasher door is fully closed, the control panel lights will display the last settings you
selected.
If you don’t want to change any of the settings, simply touch the
STArT/rESET
pad once to begin
the cycle.
If the door is closed, the indicator lights will turn off if the
STArT/rESET
pad is not pressed within
two minutes.
To activate the display, open and close the door or touch any pad.
Also, if a power failure occurs,
nOrMAl WASH
and
HEATEd dry
will automatically be
programmed.
4
5
