GE PDW8400JBB Installation Instructions Manual Download Page 4

���������

���������

METHOD 1–Air Gap with Waste Tee or Disposer

Disposer Installation

METHOD 2–High Drain Loop with Waste Tee 

or Disposer

Use the drain hose hanger included in the installation kit to 
attach the drain hose to the underside of the countertop. 
Attachment will be made in a later step.

Waste Tee Installation

Figure C

Waste Tee Installation

Disposer Installation

Figure D

Install waste tee or disposer and the air gap according to the 
manufacturer’s instructions.

Cabinet Preparation for drain line

Drill a 1-1/2" diameter hole in the cabinet wall within the 
shaded area shown in Figure A for the drain hose. Make 
sure there are no sharp edges. The drain hose will be passed 
through this hole and connected to the drain in a later step.

IMPORTANT

 – When 

connecting the drain line to a 

disposer, check to be sure that 

drain plug has been removed. 

Dishwasher will not drain if 

plug is left in place.

307Dia50

32"

Min.

18"

Min.

307Dia51

32"

Min.

18"

Min.

CAUTION

An air gap MUST BE USED if the drain hose is connected 

to waste tee or disposer lower than 18" above the floor 

level. Failure to provide the proper drain connection height 

with an air gap or 32" minimum high drain loop will result 

in improper draining of the dishwasher, which may cause 

damage.

Installation Preparation–Drain

Remove

Drain

Plug

1871 Art1

PREPARE DRAIN PLUMBING

Drain Requirements

• Drain hose must not exceed 10 feet in length.
• A high drain loop or air gap is required. See below.

Drain Method

The type of drain installation depends on the following:
• Do local codes or ordinances require an air gap?
• Is waste tee less than 18" above the fl oor?
If the answer to either question is 

yes

, an air gap must be used. 

Refer to 

Method 1

 (Figure C) in the adjacent illustrations.

If both answers are 

no

, either an air gap or high drain loop may 

be used. Refer to 

Method 1

 (Figure C) or 

Method 2

 (Figure D) in 

the adjacent illustrations 

Note

Drain hose elevation must not exceed 48".

Special consideration for a dishwasher installed on a 

elevated platform

lf the dishwasher is installed on an elevated platform, a high 
drain loop of at least 32" above the platform must be provided 
in addition to the air gap or drain loop requirement determined 
above. This is necessary for proper drain performance.

4

Summary of Contents for PDW8400JBB

















Reviews: