GE PDT660SSF2SS Installation Instructions Manual Download Page 11

STEP 15: POSITION DISHWASHER, SECURE 

TO COUNTERTOP OR CABINET

In this step you will need the 2 Phillips special head screws 
from the screws set aside in Step 1. 
The dishwasher must be secured to the countertop or the 
cabinet sides. When the underside of the countertop is wood, 
use 

Method 1

. Use 

Method 2

 when the underside of the 

countertop is made of a material, such as granite, that will not 
accept wood screws.

IMPORTANT

 –

 

 Prevent door panel and control 

panel damage. Dishwasher must be positioned so the front 

SDQHODQGFRQWUROSDQHOGRQRWFRQWDFWWKHDGMDFHQWFDELQHWV

or countertop. Mounting screws must be driven straight and 
flush. Protruding screw heads could scratch the door panel or 
control panel and interfere with door operation.

Method 1
Secure dishwasher to underside of wood countertop.

• Recheck alignment of the dishwasher in the cabinet. Refer to 

Steps 13 and 14. Door panel and/or control panel must not 
hit cabinets or countertop.

• Fasten the dishwasher to the underside of the countertop 

ZLWKWKH3KLOOLSVVSHFLDOKHDGVFUHZV5HIHUWR¿JXUH

 

0DNHFHUWDLQVFUHZVDUHGULYHQVWUDLJKWDQGÀXVKWRSUHYHQW

panel damage.

• Install plug buttons to the side of the tub well in the holes 

provided.

Method 2
Secure dishwasher to cabinet sides. 

• Recheck alignment of the dishwasher in the cabinet. Refer 

to Steps 13 and 14. Door panel and/or control panel must 
not hit cabinets or countertop. 

‡)DVWHQWKHGLVKZDVKHUWRWKHDGMDFHQWFDELQHWVZLWKWKH

2 Phillips special head screws provided. Refer to Figure X. 

0DNHFHUWDLQVFUHZVDUHGULYHQVWUDLJKWDQGÀXVKWRSUHYHQW

panel damage. Do not screw into the cabinet face frame.

• Install plug buttons to the side of the tub well in the holes 

provided.

 STEP 16:  CONNECT WATER SUPPLY

Connect water supply line to 90° elbow.

If using a flexible braided hose connection:

‡$WWDFKQXWWRƒHOERZXVLQJDQDGMXVWDEOHZUHQFK

If using a copper tubing connection:

• Slide compression nut, then ferrule over end of water line.
• Insert water line into 90° elbow.
• Slide ferrule against elbow and secure with compression nut.

IMPORTANT –

  

Check to be sure that door spring  

DQGRUGRRUVSULQJFDEOHGRQRWUXERUFRQWDFWWKH¿OOKRVHRU

water supply line.  
Test by opening and  
closing the door.    
Reroute the water  
supply lines if a  
rubbing noise or  
interference  
occurs.

Dishwasher Installation

11

Figure Y

Compression 

Nut

Hot Water 

Supply Line

90° Elbow

Ferrule

Bottom Left Side

• Re-check that the dishwasher is squarely positioned in the 

cabinet at both the top and bottom of the appliance after 

PRXQWLQJWRWKHFDELQHWVFRXQWHUWRS$GMXVWLIQHFHVVDU\

• Confirm all leveling legs are in contact with the floor to 

prevent the dishwasher from rocking and ensure proper door 
and latch operation

Brackets  Wood Countertop

Figure X

Granite Countertop

Side Brackets

Solid Surface Countertop

Summary of Contents for PDT660SSF2SS

















Reviews: