background image

TOOLS YOU WILL NEED

Read these instructions carefully and completely.

IMPORTANT –

 Save these instructions for local

inspector’s use.

IMPORTANT –

 Observe all governing codes and

ordinances.

Note to Installer – 

Be sure to leave these instructions with

the Consumer.

Note to Consumer –

 Keep these instructions for future

reference.

30” Electric Cooktop

Installation
Instructions

PCP912, PCP932, JCP346

NOTE:

 This appliance must be properly grounded.

Skill level – 

Installation of this appliance requires basic

mechanical and electrical skills.

Completion time – 

2–3 hours.

Proper installation is the responsibility of the installer.

Product failure due to improper installation is not
covered under the Warranty.

PARTS INCLUDED

1/8” Drill Bit and
Electric or Hand Drill

Phillips Head
Screwdriver

Foam Strips

4 screws

(WB1X1137)

Pub. No. 31-10638-2

05-08  JR

Printed in the United States

1

 Questions? Call 1.800.561.3344 

or

 visit our Website at:

 

www.GEAppliances.ca

2 Hold Down Brackets

Ruler or
Straightedge

Hand or
Saber Saw

Pencil

Junction Box

Wire Nuts

MATERIALS NEEDED

CAUTION: BEFORE YOU BEGIN

Safety Glasses

Summary of Contents for PCP912

















Reviews: