GE PanaFlow MV80 User Manual Download

Page: 43 / 164

PanaFlow™ MV80 & MV82 User’s Manual

Chapter 2. Installation

2.4.2 Enclosure Adjustment (Series MV80 Only)

To adjust the enclosure position, refer to

Figure 18

below and complete the following steps:

Figure 18: Enclosure Viewing Adjustment

Disconnect the power from the flowmeter.

Loosen the three set screws shown in

Figure 18

above, and rotate the display to the desired position. The

maximum allowable rotation is 180°.

Tighten the three set screws, and restore power to the meter.

CAUTION!

To avoid damage to the sensor wires, do not rotate the enclosure beyond 180° from the

original position.

Loosen three setscrews

and rotate enclosure
(maximum 180° from
original position)

Summary of Contents for PanaFlow MV80





































































































































































Search results

Summary of Contents for PanaFlow MV80

Reviews:

Related manuals for PanaFlow MV80

Brands by name

Popular brands

GE PanaFlow MV80, User Manual

Search results

Summary of Contents for PanaFlow MV80

Reviews:

Related manuals for PanaFlow MV80

Brands by name

Popular brands