manualshive.com logo in svg

GE PanaFlow HT, User Manual

Share
Download
GE PanaFlow HT User Manual Download Page 29

PanaFlow HT User’s Manual

19

Chapter 2. Installation

2.5.4 Wiring the Modbus/Service Port

The XMT900 flow transmitter is equipped with a Modbus communication port for either a connection to Vitality (PC 
software) or to a separate control system. The port is an RS485 interface.

IMPORTANT:

The maximum cable length for RS485 is 4000 ft (1200 m).

To wire to this RS485 serial port, refer to Figure 10 on page 11 and complete the following steps:

1.

Disconnect the main power to the unit and remove the rear cover.

2.

Install the required cable clamp in the chosen conduit hole on the side of the electronics enclosure.

3.

Feed one end of the cable through the conduit hole, wire it as shown in Figure 15 below.

4.

If wiring of the unit has been completed, reinstall the wiring cover on the enclosure and tighten the set screw.

Note:

Prior to use, the serial port must be programmed.

WARNING! Make sure all covers, with their O-Ring seals, are installed and the set screws tightened before 

applying power in a hazardous environment.

Figure 15: Modbus Connections

Terminal Block -Modbus Connections

PIN  Label

Description

1      MOD-            Modbus/Service Port Negative

2     MOD+            Modbus/Service Port Positive

Summary of Contents for PanaFlow HT




































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands