manualshive.com logo in svg

GE Monogram ZV950, Installation Instructions Manual, Page: 12 / 12

Share
Download
GE Monogram ZV950 Installation Instructions Manual Download Page 12

Installation Instructions

 8  INSTALL FILTERS

• Remove protective film on the filters.
• Tip the filter into the slots at the rear of the opening. 

Lift the filter and pull the knob forward until the filter 
rests on the slots.

• Install all 3 grease filters.

• To remove the filters, grasp the knob, push the filter 

towards the rear and tilt downwards. 

124Dia23

124Dia24

 9  FINALIZE INSTALLATION

• Remove the protective film covering the control  

panel on the front face of the hood, and any other 
packaging materials.

• Refer to the Owner’s Manual for operating  

instructions.

Note: 

While performing installations described in this book, 

safety glasses or goggles should be worn.

For Monogram

TM

 local service in your area, call  

1.800.444.1845.

Note: 

Product improvement is a continuing endeavor at 

General Electric. Therefore, materials, appearance and 

specifications are subject to change without notice.

Pub. No. 49-80095-1

 

04/08 JR

Printed in Italy

GE Consumer & Industrial

Appliances 

General Electric Company 

Louisville, KY 40225

ge.com

Summary of Contents for Monogram ZV950













Reviews:

No comments